Steel Structure Warehouse direct sales- Factory Suppliers Manufacturers From China

Commercial steel building is a new type of energy-saving and environmentally-friendly building system. It is known as one of the "green buildings" in the 21st century. It is an energy-saving, environmentally-friendly, and recyclable building structure.

What is the installation and welding process of commercial steel building?

The general sequence of commercial steel building welding is: pre welding inspection → preheating and derusting → installation and welding of base plate and arc striking plate → welding → inspection

1. Before commercial steel building welding, check the groove angle, blunt edge, gap and staggered joint, and remove the rust, oil stain and iron oxide scale in and on both sides of the groove.

2. Preheating. Before commercial steel building welding, gas welding or special baking gun shall be used to heat the groove and the base metal within 100mm on both sides evenly, and the surface thermometer shall be used to measure the temperature to prevent the temperature from meeting the requirements or local oxidation on the surface and preheating temperature.

3. Recheck the preheating temperature. If the temperature is not enough, reheat it to make it meet the requirements.

4. When assembling and welding the backing plate and arc striking plate, the surface cleanliness shall be the same as that of the groove surface, the backing plate shall be close to the base metal, and the arc striking plate shall be firmly welded with the base metal.

What should be paid attention to during the installation and welding of commercial steel building?

1. Welding: the weld bead of the first layer shall seal the connection between the base metal and the backing plate in the groove, and then weld layer by layer until the groove is filled. After each weld is welded, the welding slag and spatter must be removed, and the welding defects shall be ground away and repaired in time.

2. An interface must be welded continuously. If it is necessary to stop welding halfway, it shall be subject to thermal insulation and slow cooling treatment, and shall be heated again according to the regulations before re welding.

3. In case of rain and snow, commercial steel building shall stop welding. There shall be a wind shield and canopy around and above the welded junction of components. When the wind speed is greater than 5m / s, the welding shall be stopped. When the ambient temperature is lower than zero, preheating and post heating measures shall be taken for construction according to regulations.

4. Carbon structural steel shall be subject to weld flaw detection after the weld is cooled to ambient temperature, and low alloy structural steel shall be subject to weld flaw detection 24 hours after completion.

5. Welders and inspectors of commercial steel building shall carefully fill in the operation record form.

What should I pay attention to when purchasing commercial steel building?

When purchasing commercial steel building, we should pay attention to the design of waterproof, heat-insulating and anti-corrosion of the steel structure. The design documents did not specify the steel derusting grade and paint and coating thickness, and did not adopt corresponding measures according to the different fire resistance limits of different parts. commercial steel building of thermal insulation protection measures needs to be avoided.

Commercial steel building has focused on the development and production of commercial steel buildings for several years. And it commits to provide perfect service for every customer from all over the world.

Introduction of Algerian layer house building with equipment

Project equipment system：4 rows of 5-layer cage nets

Project building feeding quantity：34800 layers

Project detail: On the basis of the customer's civil chicken house, Xinguang is transformed into a modern chicken house. In terms of animal husbandry equipment and plant, the company has a professional technical research and development team, each kind of equipment designed is more suitable for animal needs, so that animals can enjoy five-star treatment. The mode of "intelligent + intelligent equipment" that we have constructed makes farming easy and simple.

Introduction of Ethiopian Prefabricated steel structural water bottling processing workshop

Located: Ethiopia

Construction area: 2000㎡

Cladding: 0.5mm galvanized sheet (No insolution)

XGZ provide design,fabrication and installation guidance as client's required.

Project picture of Ethiopian Prefabricated steel structural water bottling processing workshop

Company information of Ethiopian Prefabricated steel structural water bottling processing workshop

 A brief introduction to you about our company first, then you can contact me if there is suitable project in the future.

1200 workers, 360000 ㎡ non-dust workshop, 25 years experience, CE, ISO9001, ISO9712, ISO3834, BV, SGS certificated, one 

hour reach Qingdao port, our company, as a manufacture, this is how we keep good quality and competitive prices for global

 valued customers.

We provide steel building design, farm house design, manufacture and installation service.

Color steel insulation sandwich panel is the basic materials for steel structure buildings, which is suitable for steel structure industrial plant. It is composed of two layers of formed metal panel and directly foaming, curing molding polymer heat insulation inner core. Color steel insulation sandwich panel commonly used insulation materials are: glass wool, polystyrene(EPS), polyurethane(PU), Rock wool and other insulation materials.

Then, what's the difference between these three insulation materials?

1) Glass wool sandwich panel. Glass wool is a good inorganic thermal insulation material, glass wool is obviously characterized by good fire resistance, flame retardant and moisture absorption, and its price is cheap. The thermal conductivity of the glass wool sandwich board is not greater than 0.038 W/(m2•K).

2) Polystyrene (EPS) sandwich panel. Polystyrene is a polystyrene resin as the main raw material, through the foaming agent foaming and made of internal with numerous closed micropores. Its insulation effect is good, the price is cheap, the strength is slightly poor. Polystyrene (EPS) sandwich board, thermal conductivity is not greater than 0.038W/(m2•K).

3) Polyurethane(PU)sandwich panel. The thermal conductivity of polyurethane sandwich board is no more than 0.033 W/(m2•K), with good thermal insulation performance, good water resistance, good thermal insulation effect, high strength, foam can be made into any shape, suitable for site construction, but the price is expensive.

To meet different thermal insulation requirements, consider the thermal conductivity of the steel structure material and the thickness of the insulation layer. The thermal conductivity of commonly used steel structure insulation materials is as follows: polyurethane foam> polystyrene foam >glass wool > rock wool.

---

Xinguangzheng steel structure provide you professional technical service for steel structure buildings.

As the strategic decision to develop energy-saving and land-saving housing and construct a conservation-oriented society is further deepened and housing industrialization has become a new growth point for the world’s economic development, the development of residential steel building will be the only way for housing industrialization.

What are the advantages of residential steel building?

1. residential steel building's structural system is diversified

Many structural systems that can be used for steel structure residences have been developed, steel frame structure, steel frame-support structure, frame-tube structure (steel frame, concrete internal simplified), frame-shear wall structure (shear wall can be steel plate, concrete Or concrete with built-in steel support), light steel structure and staggered truss structure system can all be used as the structural selection of residential steel building.

2. The project cost of residential steel building is slightly higher than that of concrete or equivalent

The cost of steel structure material is higher than that of concrete, but its construction period is short, the use area is large, and the number of floors can be increased under the same conditions. The project cost of residential steel building is slightly higher or equivalent to concrete, and the actual economic benefits are significant, making residential steel building It has become the first choice for high quality and low price, and the best choice for replacing masonry structure houses in the future.

What is the future development trend of residential steel building?

residential steel building has a high technological content. The structure itself is often the architectural expression. The performance and craftsmanship of the steel structure is not only a necessary means to realize the image conception, but also has a significant impact on the architectural image, which determines that the structural conception is the success of the image conception. The key is whether or not. The progress of science and technology and the change of aesthetics will inevitably make steel structure buildings continue to expand their expression vocabulary and seek development. residential steel building sets aside the elements of style, starts from structural rationalism, and absorbs the essence from modern and traditional styles. In the future, it will be possible to create high-quality steel structure buildings with organic integration of technology and art.

What are the design considerations of residential steel building?

The residential steel building of the design structure and the stability calculation of components must cooperate with each other to make them consistent. The consistency between structural calculation and structural design has always been a problem that everyone pays attention to in structural design. For the joint connection requiring to transfer bending moment and not, sufficient stiffness and flexibility shall be given to it respectively, and the eccentricity of members shall be minimized for frame joints, which are often considered by designers when dealing with structural details. However, when it comes to stability, there are often structural requirements or special considerations different from strength. For example, in terms of flexural strength of simply supported beams, the requirement for fixed hinge support is only to prevent displacement and allow rotation in the plane. However, the above requirements are not enough when dealing with the overall stability of the beam. The support shall also be able to prevent the beam from twisting around the longitudinal axis, and allow the beam to rotate in the horizontal plane and the beam end section to warp freely, so as to meet the boundary conditions adopted for stability analysis.

Qingdao Xinguangzheng Steel Structure Co., Ltd. has been committed to providing customers with residential steel buildings and perfect after-sales service so that customers can invest easily, use them with confidence, and have no worries.

Industrial steel building mainly means that the main load-bearing components are composed of steel. Including steel pillars, steel beams, steel structure foundations, steel roof trusses (of course, the span of the factory building is relatively large, and it is basically steel structure roof trusses now), steel roof, note that steel structure walls can also be surrounded by brick walls.

• What are the characteristics of Industrial steel building?

• What are the industrial characteristics of Industrial steel building?

• Why do we have to carry out daily maintenance on Industrial steel buildings?

What are the characteristics of Industrial steel building?

The characteristics of the steel construction workshop are:

1. Industrial steel building is light, high-strength and has a large span width.

2.The construction time of industrial steelworks is short, reducing investment costs accordingly.

3. Industrial steel buildings have poor fire resistance and corrosion resistance and steel structures should not be used in areas with low temperatures.

4. Industrial steel building is easy to move and recycle without contamination.

What are the industrial characteristics of Industrial steel building?

Impact

The roofs of flat buildings are mostly inclined roofs, so that the roof construction essentially uses a triangular roof chair system made of cold-formed steel components. The light steel components form a very strong structure after sealing the building plates and plasterboard plates. "Plate-rib structural system", the industrial steel structure of this structure has a stronger earthquake resistance and resistance to horizontal loads and is suitable for areas with earthquake intensities above 8-degree.

Air resistance

The Industrial steel building has a low weight, a high strength, a good overall stiffness and a strong deformability. The building weighs only a fifth of the brick concrete construction and holds a hurricane of 70 meters per second so that life and property can be effectively protected.

Durability

The housing structure of the Industrial steel building consists entirely of cold-formed thin-walled steel component systems. The steel frame consists of a high-strength, cold-rolled, fire-soaked super-corrosion protection sheet which effectively avoids the influence of steel sheet corrosion during construction and use and increases the durability of light steel components. The durability of the structure can reach 100 years.

Why do we have to carry out daily maintenance on Industrial steel buildings?

Industrial steel buildings must be regularly cleaned and maintained. Under normal circumstances, it must be inspected and maintained once a year. When cleaning the outer wall of the Industrial steel building, you must be careful not to contaminate anything. Do not use steel wire balls, brushes and other abrasive cleaning agents. If you use clean water, you should rinse from top to bottom. The branches, leaves and similar objects on the Industrial steel building should be cleaned in time to avoid unnecessary problems due to the delay. If the surface of the metal plate for industrial steelmaking is damaged, it should be repaired in time to prevent the surface of the metal plate from corroding by sun and rain. If necessary, use all coated high-elastic nanomaterials to protect the metal roof plate, act effectively in thermal insulation and sealing and save energy for room climate.

Seeing this, do you also want to order a Industrial steel building? If necessary, you can contact Qingdao Xinguangzheng Steel Structure Co., Ltd. they will provide the Industrial steel building of the best quality.

Steel structures are a new type of construction system that offers the benefits of low weight, easy installation, short construction time, good seismic performance, fast investment recovery and low environmental pollution. It is therefore generally preferred by all parties in the industry. Under the call for green construction, energy saving, environmental protection and resource recycling, steel structures have gradually become widespread in agricultural steel building and the scale of the steel construction industry has expanded further.

• What are the requirements for the operating equipment of agricultural steel building?

• What are the technical requirements for agricultural steel building?

• What are the construction requirements for agricultural steel building?

What are the requirements for the operating equipment of agricultural steel building?

1. The machinery and equipment of the agricultural steel building are operated and maintained by designated personnel, and the operating certificates are complete.

2. Mechanical operation part and on-site electricity requirements:

a. The rotation and dangerous parts of various machines and electric machinery must be equipped with protective devices.

b. Electrical equipment and wiring must be well insulated, with rain-proof and moisture-proof facilities.

c. The electrical box has a door, color code and number, which meet the installation height. The high-voltage leakage protector and zero grounding are complete. The switch box and electrical equipment must be "one machine, one switch, one leakage", and the fuse and actual equipment load Match.

d. When installing electrical equipment, the switches, circuits, grounding devices, etc. must be inspected, and they must be intact and undamaged, with good insulation.

What are the technical requirements for agricultural steel building?

(1) The agricultural steel building has a reasonable structure, a 360-degree undercut connection, and no bolts on the roof, which completely avoids water seepage and water leakage.

(2) Adopt self-fixing bolts to fix, simplify the operation and greatly reduce the labor intensity of workers. There is no need to set up a scaffold fixing nut, which improves the safety of operation.

(3) The boom of agricultural steel building is detachable and the angle can be adjusted freely, which is suitable for simultaneous construction of arch roofs with multiple spans.

What are the construction requirements for agricultural steel building?

1. First, according to the functional requirements of agricultural steel building, adopt a corresponding reasonable structure system. Achieve advanced technology, novel structure, and achieve the unity of architecture and structure.

2. The agricultural steel building is mostly based on rods, so the size of the rods is as modular and standardized as possible, which is convenient for mechanized manufacturing, transportation, installation, and improves productivity.

3. The agricultural steel building adopts high-efficiency steel with high economic indicators.

4. The nodes of agricultural steel building are very important. Appropriate connection methods should be adopted to make the node design consistent with the simplified structural calculation model. In the past, most of the structural damage occurred at the nodes, so the nodes must be carefully designed and constructed. Advanced and reliable connection methods are used.

Qingdao Xinguangzheng Steel Structure Co., Ltd. employs more than 100 workers, through the efforts of their entire staff, the agricultural steel buildings of high quality, widely used in a variety of architecture, have shared the broad masses of the worldwide market for over a decade.

Prefab House refers to the use of industrial production methods to build houses, that is, the stairs, exterior walls, balconies, air-conditioning panels, etc. of the house are all prefabricated in the factory outside the construction site, and then shipped to the construction site for "assembly", and the interior of the house will be refined at one time. Handed over after renovation. That is, the huge external walls, stairs, and balconies from the factory are "assembled" on the construction site into houses and buildings.

• What are the advantages of a Prefab House?

• What are the structural types of Prefab Houses?

• What should we be careful about when selecting a Prefab House?

What are the advantages of a Prefab House?

1. Safe and reliable

The Prefab House with steel as the main building material has a high capacity per volume unit, is more stable and solid than the traditional brick and brick concrete technology, has a better seismic performance, wind resistance, water density and refractory performance and also has thermal insulation and sound protection functions. Steel has good ductility and can better use the energy brought in by earthquakes, so it has good seismic performance and a high structural security t hat guarantees the safety of stay.

2. Easy construction and short construction time

All components are prefabricated in the factory and only have to be installed on site, which greatly shortens the construction cycle. A 6000-square-metre-long building can basically be installed in 40 days.

What are the structural types of Prefab Houses?

1. Structural system

The structure of the Prefab House can be divided into: steel frame system, steel frame support system, steel frame-core tube system, steel frame-module-core tube system and steel frame-shear-wall system. With the continuous development of the technology, newer steel construction systems will also appear.

2. Peripheral protection system

The outer protective system of the Prefab House can be divided into blocks, plates, cans and other types.

3. Internal system

Traditional construction has many disadvantages. For example, the traditional rough decoration method does not separate the interior system and the structural system, which makes it difficult to adapt to the modern development of the housing industry; the house technology lines are not separated and the water and power lines are buried in the support layer, which the "century residence" cannot realize." The waste of social resources is serious.

What should we be careful about when selecting a Prefab House?

1.The costs are relatively higher than in the traditional Prefab House made of brick concrete and concrete.

2. The steel structure of the Prefab House, with its unique steel structure, walls, roofs and other materials, as well as the standardized and final internal distribution and support facilities, is difficult to adapt to the habits of people "arbitrarily handling the house".

3. Corrosion of steel: Al-galvanized steel must be used for maximum corrosion protection and the main steel structure can reach fifty years.

4. There are many requirements for new materials. The structure of steel houses is equipped with materials such as thermal insulation and heat protection, usually using new lightweight materials.

Prefab Houses produced by Qingdao Xinguangzheng Steel Structure Co., Ltd. feature attractive appearance, excellent performance, user-friendly operation, easy maintenance, and internationally advanced performance indicators, and are exported to more than 10 countries and regions.

1/1/2021· Sadaf, Soofer Co.’s in-house brand. Founded in 1982, Soofer is a wholesaler, manufacturer, and distributor of Mediterranean, Middle Eastern, Kosher, and Halal foods. They have over 1,200 products with 50% distributed in California, 40% exported outside California to other states, and 10% exported outside the country.

Hangars constructed from steel are extremely wind and fire resistant and are expertly sealed to prevent mold growth, mildew, termites or other pests from intruding. Lower insurance costs due to the safety are just an added bonus to any steel structure. Speedy Processes Pre-fab steel hangars do not require lengthy processes.

RECO SERIES. The RECO series creates a relaxed, stylish and trendy office space for people. It has natural textures and colors, it has rich functional creativity, it has personalized combinations and collocations, and it has different price levels. View More.

7/1/2022· RAMESH TUNGARIYAI India Date Posted: 30-Jan-2022 Contact Buyer Chicken run cages walk in coop for poultry dog rabbit hen cage pen metal door house Im from India. I need to import this. My **** number is 919895359239 sarath8001@ **** Sarath S India Date Posted: 29-Jan-2022 Contact Buyer

Connect2India providers end to end solutions to export Steel Structures from any country in the world. Find Steel Structures buyers from 100 countries. We provide help and support in Steel Structures export documentation, Steel Structures export procedure, logistics, shipment and goods delivery to the specified location.

Website: Prefabricated House Supplier/ Container House China / China Prefabricated House Head Office: 5th Floor, Building A, Darron Center,No.180,Haier Road, Qingdao, 266000,China Lida Group

Located in Ahmadabad’s burgeoning suburb Prahladnagar on the S.G. Highway, the ensemble offers a total floor space of 17,000 square meters, of which 3,600 comprise commercial space, as well as ten storeys for office usage. During the day, the striking structure of the curtain facade defines the two buildings.

Prefabricated villas andhouses are less costly than traditional houses. There are multiple factors that ensure low cost. The price of a completed home is determined by the floor plan, design and customizations preferred by the customer. At the same time, transportation conditions, location and land are among the factors that affect the cost.