Prefabricated Building manufacturer- China Factory Manufacturers Suppliers

Industrial steel building mainly means that the main load-bearing components are composed of steel. Including steel pillars, steel beams, steel structure foundations, steel roof trusses (of course, the span of the factory building is relatively large, and it is basically steel structure roof trusses now), steel roof, note that steel structure walls can also be surrounded by brick walls.

• What are the characteristics of Industrial steel building?

• What are the industrial characteristics of Industrial steel building?

• Why do we have to carry out daily maintenance on Industrial steel buildings?

What are the characteristics of Industrial steel building?

The characteristics of the steel construction workshop are:

1. Industrial steel building is light, high-strength and has a large span width.

2.The construction time of industrial steelworks is short, reducing investment costs accordingly.

3. Industrial steel buildings have poor fire resistance and corrosion resistance and steel structures should not be used in areas with low temperatures.

4. Industrial steel building is easy to move and recycle without contamination.

What are the industrial characteristics of Industrial steel building?

Impact

The roofs of flat buildings are mostly inclined roofs, so that the roof construction essentially uses a triangular roof chair system made of cold-formed steel components. The light steel components form a very strong structure after sealing the building plates and plasterboard plates. "Plate-rib structural system", the industrial steel structure of this structure has a stronger earthquake resistance and resistance to horizontal loads and is suitable for areas with earthquake intensities above 8-degree.

Air resistance

The Industrial steel building has a low weight, a high strength, a good overall stiffness and a strong deformability. The building weighs only a fifth of the brick concrete construction and holds a hurricane of 70 meters per second so that life and property can be effectively protected.

Durability

The housing structure of the Industrial steel building consists entirely of cold-formed thin-walled steel component systems. The steel frame consists of a high-strength, cold-rolled, fire-soaked super-corrosion protection sheet which effectively avoids the influence of steel sheet corrosion during construction and use and increases the durability of light steel components. The durability of the structure can reach 100 years.

Why do we have to carry out daily maintenance on Industrial steel buildings?

Industrial steel buildings must be regularly cleaned and maintained. Under normal circumstances, it must be inspected and maintained once a year. When cleaning the outer wall of the Industrial steel building, you must be careful not to contaminate anything. Do not use steel wire balls, brushes and other abrasive cleaning agents. If you use clean water, you should rinse from top to bottom. The branches, leaves and similar objects on the Industrial steel building should be cleaned in time to avoid unnecessary problems due to the delay. If the surface of the metal plate for industrial steelmaking is damaged, it should be repaired in time to prevent the surface of the metal plate from corroding by sun and rain. If necessary, use all coated high-elastic nanomaterials to protect the metal roof plate, act effectively in thermal insulation and sealing and save energy for room climate.

Seeing this, do you also want to order a Industrial steel building? If necessary, you can contact Qingdao Xinguangzheng Steel Structure Co., Ltd. they will provide the Industrial steel building of the best quality.

Steel structure workshop is composed of frame, beam, wall and weighing column, etc. In the design of single-layer steel structure workshop, the first thing to ensure that the structure of the workshop does not affect the use of the second in the design time to calculate the bearing force of the beam, the selection of materials to meet the relevant standards.

Composition of single-layer steel structure workshop:

1. Transverse frame: composed of columns and the roof truss or roof beam supported by it, it is the main load-bearing system of the steel structure of single-storey workshop. It bears the dead weight of the structure, the wind and snow loads and the vertical and horizontal loads of the crane, and transfers these loads to the foundation.

2. Roof structure: structural system bearing roof load, including transverse frame beam, bracket, middle roof frame, skylight frame, purlin and so on.

3. Support system: including the support of the roof part and the support between columns. On the one hand, it forms the longitudinal frame of the steel structure of the single-storey workshop with columns and crane beams to bear the longitudinal horizontal load; On the other hand, the main load-bearing system is connected by individual plane structure into the whole structure of space, so as to ensure the necessary stiffness and stability of the steel structure of the single-storey workshop.

4. Crane beam and brake beam (or brake truss) : mainly bear the vertical and horizontal load of the crane, and transfer the load to the transverse frame and longitudinal frame.

5. Wall frame: Bear the dead weight and wind load of the wall.

Single-layer steel structure plant design points:

1. In the column network arrangement of single-storey steel structure buildings, when column spacing is not equal, especially the column spacing of each longitudinal column column, the columns should be arranged on the common horizontal positioning axis to ensure the stiffness requirements of the workshop, so that the workshop can be used normally.

2. For the temperature expansion joint section length of single-storey steel structure building, it is better to set the expansion joint when the plant structure exceeds the designed value under special circumstances. This has the advantage of being separated into independent structures, making temperature changes negligible after a drop.

3. The transverse frame calculation of single-storey steel structure building. The transverse frame structure transfers the load and action of the plant structure to the foundation, which is the main load-bearing structure of the plant.

4. Calculation of longitudinal force transmission system of single-storey steel structure building, steel column, column.

---

Qingdao Xinguangzheng steel structure group is a leading manufacture in China. With 25 years experience, we have confidence to provide you the highest cost performance.

Qingdao Activa Group is the largest outdoor leisure products R & D and production enterprise in the world. It has established factories and branches in 14 countries and regions. Currently, it has five hundred year brands in its industry, and 1820 patents at home and abroad. The first phase project of Qingdao Activa Group, which is contracted by our company, has a total construction area of over 80000, which is the general contracting project.

Residential steel building is lightweight and high-strength. For buildings of the same weight, the steel structure has a small cross-section and a large net height, which can save building height. The number of layers of steel structure is more than that of concrete, which not only increases the building area, but also brings good economic benefits.

• What are the advantages of Residential steel building?

• What raw materials should be used for the walls of Residential steel building?

• What is the roof system of Residential steel building?

What are the advantages of Residential steel building?

1. Superior seismic performance

Compared with traditional residential structures, Residential steel building is a flexible structure and has a lighter weight. Therefore, buildings with the same fortification intensity and the same site will bear less seismic force, and the earthquake disaster caused by them will be weakened accordingly. The use of steel in the earthquake zone Structural housing will reduce casualties and property losses, with considerable comprehensive benefits.

2. Flexible layout and increased effective use area

Residential steel building adopts steel structure, which can realize large span under the premise that the cross-section is not too large, which makes the building function very flexible and can be flexibly arranged according to the needs of residents, which is conducive to meeting the needs of modern homes and adapting The needs of the modern housing market. Moreover, the steel structure is adopted, the cross-section of the beams and columns is small, and the use area of the residents is increased at the same time.

What raw materials should be used for the walls of Residential steel building?

Residential steel building's steel frame system, steel frame-support system, steel frame-concrete core tube (shear wall) system outer walls can be filled with small concrete block walls, autoclaved lightweight aerated concrete slabs, and prefabricated reinforced concrete walls Board, steel wire mesh frame polystyrene sandwich panel, fiber cement external wall hanging panel, polyurethane composite external wall panel, metal surface embossed composite panel, etc. The inner wall can be made of glass fiber strong gypsum hollow board, fiber cement board infusion (foam concrete) wall, light composite wall board, etc.

What is the roof system of Residential steel building?

1. The flat roof of the Residential steel building adopts steel beams (I-beam, C-shaped steel), prefabricated reinforced concrete roof panels, and thermal insulation and waterproof layer.

2. The sloping roof of Residential steel building adopts portal frame, truss, light steel keel truss (bracket), I-shaped (or C-shaped) and steel purlin, colored cement tile, colored steel plate tile and colored asphalt tile roof. Thermal insulation and waterproof layer should also be used in the slope roof. The thickness of the insulation layer is determined by thermal calculation and meets the requirements of energy-saving design standards.

It is an important choice in residential building construction. A good Residential steel building starts with the best engineering staff, and Qingdao Xinguangzheng Steel Structure Co., Ltd. is always ready to help you meet your technical and practical requirements.

Commercial steel building is a new type of energy-saving and environmentally-friendly building system. It is known as one of the "green buildings" in the 21st century. It is an energy-saving, environmentally-friendly, and recyclable building structure.

What is the installation and welding process of commercial steel building?

The general sequence of commercial steel building welding is: pre welding inspection → preheating and derusting → installation and welding of base plate and arc striking plate → welding → inspection

1. Before commercial steel building welding, check the groove angle, blunt edge, gap and staggered joint, and remove the rust, oil stain and iron oxide scale in and on both sides of the groove.

2. Preheating. Before commercial steel building welding, gas welding or special baking gun shall be used to heat the groove and the base metal within 100mm on both sides evenly, and the surface thermometer shall be used to measure the temperature to prevent the temperature from meeting the requirements or local oxidation on the surface and preheating temperature.

3. Recheck the preheating temperature. If the temperature is not enough, reheat it to make it meet the requirements.

4. When assembling and welding the backing plate and arc striking plate, the surface cleanliness shall be the same as that of the groove surface, the backing plate shall be close to the base metal, and the arc striking plate shall be firmly welded with the base metal.

What should be paid attention to during the installation and welding of commercial steel building?

1. Welding: the weld bead of the first layer shall seal the connection between the base metal and the backing plate in the groove, and then weld layer by layer until the groove is filled. After each weld is welded, the welding slag and spatter must be removed, and the welding defects shall be ground away and repaired in time.

2. An interface must be welded continuously. If it is necessary to stop welding halfway, it shall be subject to thermal insulation and slow cooling treatment, and shall be heated again according to the regulations before re welding.

3. In case of rain and snow, commercial steel building shall stop welding. There shall be a wind shield and canopy around and above the welded junction of components. When the wind speed is greater than 5m / s, the welding shall be stopped. When the ambient temperature is lower than zero, preheating and post heating measures shall be taken for construction according to regulations.

4. Carbon structural steel shall be subject to weld flaw detection after the weld is cooled to ambient temperature, and low alloy structural steel shall be subject to weld flaw detection 24 hours after completion.

5. Welders and inspectors of commercial steel building shall carefully fill in the operation record form.

What should I pay attention to when purchasing commercial steel building?

When purchasing commercial steel building, we should pay attention to the design of waterproof, heat-insulating and anti-corrosion of the steel structure. The design documents did not specify the steel derusting grade and paint and coating thickness, and did not adopt corresponding measures according to the different fire resistance limits of different parts. commercial steel building of thermal insulation protection measures needs to be avoided.

Commercial steel building has focused on the development and production of commercial steel buildings for several years. And it commits to provide perfect service for every customer from all over the world.

Industrial steel building has a wide range of applications and can be used in factories, warehouses, office buildings, stadiums, hangars, etc. to be used. It is suitable not only for single-storey large-space buildings, but also for the construction of multi-storey or high-rise buildings.

• What are the architectural features of industrial steel building?

• What is the reason why more and more people are choosing industrial steel building?

• What types of construction are available for industrial steel buildings?

What are the architectural features of industrial steel building?

Insulation: Avoid heat transfer on both sides of the metal roof to ensure that the ambient air temperature is stable. The thermal protection function is realized by filling thermal protection materials (usually used glass wool and stone wool) under the metal roof plate. The heat conservation effect is expressed by the U-value and the unit is W/M2K. The thermal insulation performance is determined by the following factors: raw material, density and thickness of the thermal insulation cotton; the humidity of the thermal insulation wall, the method of connecting the metal roof plate and the underlying structure (to prevent the phenomenon of the "cold bridge"), the repeated ability of the metal coating to heat radiation.

Daylight: Improve indoor lighting during the day by means of skylights and save energy. When installing daylight panels or daylight glass at certain positions on the metal roof, the duration of the daylight should be adjusted to the metal ceiling panel and the connection between the daylight and the metal ceiling panel should be treated watertight.

What is the reason why more and more people are choosing industrial steel building?

Beautiful: The metal roof of the industrial steel building has a good texture and a pleasant color.

Check the heat expansion and contraction: check the contraction shift and direction of the metal roof plate. Make sure that in areas with high temperature differences the metal roof plate is not damaged by heat expansion and contraction.

Anti-avalanche: install snow barriers on the metal roof in snow-covered areas to prevent a sudden fall of snow.

Anti-ice caps: industrial steel building can prevent rain and snow from forming ice caps on the mould.

What types of construction are available for industrial steel buildings?

The frame of the industrial steel building is the main structure of the system frame. It is a flat structure consisting of columns and frames. All horizontal water loads and most vertical loads are transferred to the foundation via the plant frame. In industrial buildings, the industrial steel building frame has the following three most common types of construction;

1. The single-storey steel structure factory building frame is a single-storey frame formed from the stacked column of the factory building and the frames anchored to the top of the column (the column top can be called the system bent when the column top is foldable).

2. A rigid one-storey frame, a one-storey frame formed by a rigid connection of columns with an equal or gradual cross-section and frames on the top of the column.

3. Multi-layered frame, a multi-layered frame formed by joining columns and floor supports (or specialist works) and roof supports or roof supports.

Having learned so much about industrial steel building, it is also a difficult problem to select from many manufacturers the one with high quality and low price. Qingdao Xinguangzheng Steel Structure Co., Ltd. has been a Chinese pioneer in industrial steel building for several years. You can work with customers from design to completion to ensure that all technical requirements are met.

Project Introduction:

Solomon office project is a two-story frame structure, with a building area of more than 1500 square meters. The first floor is maintained as aluminum-plastic plate curtain wall and part of glass curtain wall, the second floor is maintained as glass curtain wall, the roof is glass wool composite plate, and the parapet part is aluminum-plastic plate.

 

Personnel involved in design and construction refinement: Liu Kangning, Jing Yanyan

Total project amount: 2.94 million

 

Detailed address: Honiara, Solomon Islands

The following project related parameters:

Area: 1500 square meters

Eave height: 7M

Ridge height: 8M

Number of floors: two

Wind speed: 176km / h

Load: second floor load: 450kg / m2, roof: 30kg / m2

Shapes: Framing

Steel consumption: 90 tons

Purpose: Salomon Telekom office and warehouse

 

 

Detail of Prefabricated Steel Structure Building Office in Solomon

 

Main Characters of prefab steel warehouse

· Super Aseismatic

Most part of the structure will be consisted of cold formed steel members, this system aseismatic grade can reachto 8.

· Wind Resistance

Steel structure building has the performance of high strength, solid rigidity and good deformation capacity, can resist strong wind for 50m/s.

·Durable

The steel material will be painted or galvanized as customers' requirement to be more anticorrosion and rustproof, the lifespan of the structure can be reach to 50~70 years.

·Heat Insulation

Sandwich panel can improve the insulation performance of the building, effectively avoid the phenomenon of "cold bridge" wall

·Environment Protection

Little waste for pollution in construction, 100% steel structure materials can be recycled, most of other related materials also can be recycled.

·Easy and Fast Build

Dry construction, will not influenced by the weather and environment, save much time and labor cost. One 300m2 steel structure building, can be finished in 30 days by only 5 workers.

The project of steel structure hangar for African market constructed by Xinguangzheng Group has been completed smoothly. The Niger hangar project need comprehensive consideration, and a severer designing demand. The client has also a higher requirement for the portal.

Given the strictly demand for portal, Xinguangzheng has offered the most specialized blue print as well as installation services, and has finished the project excellently. We have thus gained our clients' trust and support.

Xinguangzheng will continuously seek for technical breakthroughs and new products, offer integrated settlements, and provide our clients with best products and best services, to give our clients more happiness.

 

2/3/2022· Prefer steel chicken house project 2022-03-02 Poultry house is a type of buildings to protect chickens (broilers and layers) from bad weathers and provide the chickens living space with feeding system, drinking system, waste cleaning and other equipment.

Popular Poultry Sheds Products Steel Industrial Poultry Shed ? 280 / Square Feet M/s Repromachines Contact Supplier Poultry Sheds ? 180 / Square Feet Rays Design …

Steel Hangar Price 48,654 products found from 1,247 Steel Hangar Price manufacturers

Serving Calgary

Only when all the details have been worked out will you know the true cost of this metal building! Typically, steel buildings cost US

Steel Modern Prefabricated Houses ? 750 / Sq ft JBFS Engineering Systems Private Limited Contact Supplier Steel Prefabricated Farm House ? 1,400 / sq ft CND Engineering Private Limited Contact Supplier Mild Steel Prefab House Structure ? 300 / Square Feet Asaebrima Infrastructure And Projects Private Limited Contact Supplier

25/12/2021· UK Steel Importers, Buyers and Distributors - Tradekey. All RFQs > United Kingdom Importers > Steel Buyers (1,039 buy offers Found) Page 1 of 35.

With in-stock steel products including universal beams, universal columns, rounds, hollow section, bright bars and many more, we have an extensive product range to cater for any requirement with free bespoke cutting and depot collection. With in house experts on all stocked items we can offer much more than a competitive pricing, peace of mind.