India Industrial steel building make money- Factory Manufacturers Suppliers From China

Commercial steel building is a new type of energy-saving and environmentally-friendly building system. It is known as one of the "green buildings" in the 21st century. It is an energy-saving, environmentally-friendly, and recyclable building structure.

What is the installation and welding process of commercial steel building?

The general sequence of commercial steel building welding is: pre welding inspection → preheating and derusting → installation and welding of base plate and arc striking plate → welding → inspection

1. Before commercial steel building welding, check the groove angle, blunt edge, gap and staggered joint, and remove the rust, oil stain and iron oxide scale in and on both sides of the groove.

2. Preheating. Before commercial steel building welding, gas welding or special baking gun shall be used to heat the groove and the base metal within 100mm on both sides evenly, and the surface thermometer shall be used to measure the temperature to prevent the temperature from meeting the requirements or local oxidation on the surface and preheating temperature.

3. Recheck the preheating temperature. If the temperature is not enough, reheat it to make it meet the requirements.

4. When assembling and welding the backing plate and arc striking plate, the surface cleanliness shall be the same as that of the groove surface, the backing plate shall be close to the base metal, and the arc striking plate shall be firmly welded with the base metal.

What should be paid attention to during the installation and welding of commercial steel building?

1. Welding: the weld bead of the first layer shall seal the connection between the base metal and the backing plate in the groove, and then weld layer by layer until the groove is filled. After each weld is welded, the welding slag and spatter must be removed, and the welding defects shall be ground away and repaired in time.

2. An interface must be welded continuously. If it is necessary to stop welding halfway, it shall be subject to thermal insulation and slow cooling treatment, and shall be heated again according to the regulations before re welding.

3. In case of rain and snow, commercial steel building shall stop welding. There shall be a wind shield and canopy around and above the welded junction of components. When the wind speed is greater than 5m / s, the welding shall be stopped. When the ambient temperature is lower than zero, preheating and post heating measures shall be taken for construction according to regulations.

4. Carbon structural steel shall be subject to weld flaw detection after the weld is cooled to ambient temperature, and low alloy structural steel shall be subject to weld flaw detection 24 hours after completion.

5. Welders and inspectors of commercial steel building shall carefully fill in the operation record form.

What should I pay attention to when purchasing commercial steel building?

When purchasing commercial steel building, we should pay attention to the design of waterproof, heat-insulating and anti-corrosion of the steel structure. The design documents did not specify the steel derusting grade and paint and coating thickness, and did not adopt corresponding measures according to the different fire resistance limits of different parts. commercial steel building of thermal insulation protection measures needs to be avoided.

Commercial steel building has focused on the development and production of commercial steel buildings for several years. And it commits to provide perfect service for every customer from all over the world.

Qingdao Xinguangzheng Steel Structure Group completed Qingdao Haier Yungu Supporting School Project on August 31, 2022.

The main structure of the commercial steel building can be installed simultaneously with the wall panel. The main structure and the wall panel are fixed by embedded parts and connectors, which is convenient for installation. It only needs to be hoisted in place, connected and fixed, and the three links of joint treatment are not required. No need for secondary grouting, and has the advantages of short construction period, high assembly rate, good integrity, and good wind pressure resistance.

What are the welding sequence and process parameters of commercial steel building typical nodes?

(1) When the sides of the upper and lower columns without ear plates are symmetrically welded to 1/3 of the plate thickness by two welders on both sides, cut off the ear plates.

(2) Then two welders are symmetrically welded on both sides to 1/3 of the plate thickness on the side where the ear plate is cut off.

(3) Two welders will be responsible for the welding of two adjacent sides.

(4) The joints of the weld bead between every two layers should be staggered with each other, and the weld bead joints welded by two welders should also pay attention to the stagger of each layer. Pay attention to the temperature between the layers during the welding process.

(5) Welding process parameters:

CO2 gas shielded welding: wire diameter Φ1.2mm, current 280～320A, welding speed 350～450mm/min

Extending length of welding wire: about 20mm, gas flow rate 25～80L/min,

Voltage 29～34V, interlayer temperature 120～150℃

What points should be paid attention to when installing commercial steel building?

We must prefabricate and assemble commercial steel building steel components on the steel platform in accordance with the installation sequence and process requirements, and ensure the quality of welding production.

The spacing between the splicing seam of the splicing flange plate and the splicing seam of the web plate of the section steel should be greater than 200 mm. The splicing length of the flange plate shall not be less than 2 times the plate width; the splicing width of the web shall not be less than 300 mm, and the length shall not be less than 600 mm.

In order to facilitate the welding of commercial steel building and ensure the welding quality, try to weld the reinforcement plates, connecting plates, backing plates, and overhanging beams (beams) on the columns and beams on the ground steel platform according to the dimensions of the construction drawings.

In addition to the fabrication and assembly of steel components prefabricated on the steel platform according to the construction drawings and specifications, the process and installation dimensions of the commercial steel building on-site installation should also be considered.

What is the social significance of commercial steel building?

The construction of commercial steel building has trained a new generation of construction and installation industrial workers. Factory production and mechanized installation avoid the high dependence of the traditional construction industry on labor, moderately reduce the impact of high labor costs brought on by the aging of the global population on the development of the industry, and predictably cultivate a new generation of construction and installation industry workers. It is of far-reaching significance to the sustainable development of the construction industry.

Qingdao Xinguangzheng Steel Structure Co., Ltd. has focused on the development and production of commercial steel buildings for several years. And it commits to provide perfect service for every customer from all over the world.

Introduction of Maldives Prefabricated Steel Structure Construction Mall Building Hardware Store:

Project Area: 3323 ㎡       

Project Date: 2017

Project Detail: Six-story steel structures, 100mm fiberglass wool sandwich panel for roof and Glass Curtain +Aluminum Wall Cladding for outer wall and 75mm rock wall sandwich panel as inter wall. The fireproof grade is grade 2, and the fireproof coating is indoor thin fireproof coating.

Effect picture of Maldives Prefabricated Steel Structure Construction Mall Building Hardware Store :

Company information

Qingdao Xinguangzhegn steel structure group company has 1200 workers, 360000 ㎡ non-dust workshop, 25 years experience, CE, ISO9001, ISO9712, ISO3834, BV, SGS certificated, one hour reach Qingdao port, our company, as a manufacture, this is how we keep good quality and competitive prices for global valued customers.

We provide steel building design, farm house design, manufacture and installation service.

Introduction of Qingdao Jiaodong International Steel Structure Building Airport 

Qingdao Jiaodong International Airport (comprehensive transportation center and parking building) project is constructed by open cut method. The buried depth of the structure bottom is about 2.5m, and the wall wrapping surface is about 3.5m * 0.85m.

The column is made of Φ 850 * 25 / φ 700 * 16 straight seam concrete-filled steel tubular column, and the upper and lower columns are welded by variable diameter (φ 850 ~ φ 700). The total height is about 30 meters, and the total weight is about 20 tons. It is transported to the construction site in 17m + 13m sections. Each steel pipe column is made of 25 mm or 16 mm thick steel plate.

Factory processing assembly with an error of ± 2mm to meet the requirements, the construction site using a 250t crane for installation.

Generally speaking, the installation procedures of industrial steel building include installation of steel columns, installation of inter-column supports, temporary installation of steel crane beams, roof beams, roof supports, steel crane beams, etc., correction, fixation, and structural installation of maintenance.

• What is the specific process of industrial steel building construction?

• How to regularly maintain industrial steel building?

• How to consider the cost of industrial steel building construction?

What is the specific process of industrial steel buildings?

1. Lifting the main structure of industrial steel buildings: connecting steel carriers on the ground, erecting steel columns, lifting steel carriers, connecting secondary structures, correcting the deviation of the main structure, installing crane carriers (optional), lifting intermediate layers (optional), and coating with fire resistant paint pack.

Main control quality: The deviation of the main structure should meet the specifications and design requirements and the initial and final application of high-strength screws should meet the requirements.

2. Installation of secondary structure: roofing posts, roof wall supports, flange supports, etc.

3. Laying of roof plate and insulation layer: first lay insulation layer, then assemble roof plate (in some projects a position of steel fabric is also placed under the insulation layer to prevent a fall of the insulation layer, this mainly depends on insulation layer level)

Main quality control: The roof is mainly waterproof, therefore the plate should be covered with the plate, the nail position, the glue coating should be full or not, the glue should be wiped clean and the coating on the surface of the plate should not be damaged to rust etc. to avoid.

How to regularly maintain industrial steel building?

industrial steel building wall maintenance and installation: mainly the installation of wall insulation and wall panels.

The main quality control of industrial steel building: the wall is mainly an aesthetic problem, and a window area is waterproof. There is also the problem of installation deviation. For example, the bottom should be flat, the entire plane should be flat, the flatness deviation between the board and the board should meet the requirements, and so on.

The detailed structure of the industrial steel building: mainly the installation of some trims, such as the wrap angle between the roof and the wall, the wrap angle at the corner of the wall, the flooding board between the wall panel and the brick wall, the door and window trim, etc.

How to consider the cost of industrial steel building construction?

The price of industrial steel building can only be compared with certain basic conditions, such as whether it is imported or domestic color panels, its thickness, coating; insulation material and thickness; whether there is a skylight; workshop bays and spans; whether there are cranes, crane tonnage, Many factors such as the level of the work system are related, and the impact of the price difference in other regions and the qualification level of the construction unit cannot be ignored.

The industrial steel building has achieved an irreplaceable position in industrial production. Qingdao Xinguangzheng Steel Structure Co., Ltd. is committed to providing different kinds industrial steel buildings of high quality for all customers from all over the world.

Introduction of Algerian layer house building with equipment

Project equipment system：4 rows of 5-layer cage nets

Project building feeding quantity：34800 layers

Project detail: On the basis of the customer's civil chicken house, Xinguang is transformed into a modern chicken house. In terms of animal husbandry equipment and plant, the company has a professional technical research and development team, each kind of equipment designed is more suitable for animal needs, so that animals can enjoy five-star treatment. The mode of "intelligent + intelligent equipment" that we have constructed makes farming easy and simple.

A lot of work is needed to promote and improve the design specifications and construction technical standards of different types of structures, and to develop new types of lightweight insulation wall materials and the supporting issues of residential components. At the same time, it is necessary to widely publicize the advantages of the development of Residential steel building, so that more developers, designers and users can understand and understand steel structure housing.

• What are the main forms of Residential steel building?

• What are the structural characteristics of these Residential steel buildings?

• What should I pay attention to when using Residential steel building?

What are the main forms of Residential steel building?

Judging from the Residential steel building that has been built, the king has:

1) Thin-walled steel composite wall panel form;

2) Pure frame form;

3) Frame support form;

4) Form of steel-concrete combination;

5) Steel frame-concrete seismic wall form and so on.

What are the structural characteristics of these Residential steel buildings?

The structural forms of Residential steel building have their own characteristics. Among them, the thin-walled steel composite wall panel is particularly suitable for finalized products. The Residential steel building system evolved from the wall panel structure, that is, the thin-walled steel column members are arranged at a distance of about 600mm. The vertical load-bearing structure and section steel have a support system to resist horizontal forces. The floor slab is arranged as a multi-rib support structure according to the position of the vertical section steel. Because the upper structure is a wall-like structure, the foundation is set as a strip foundation according to the force. The foundation requirements are not high.

The thin-walled steel composite wallboard residence is affected by the dense structure, and there are certain restrictions on the size of the partitions, door, door and window openings, and pick-out components.

What should I pay attention to when using Residential steel building?

The latter several forms of Residential steel building can meet the design requirements of multi-story residential buildings, but there is a common problem from the perspective of use, that is, the impact of the prominent beams and columns on the interior look and feel of the residence.

Compared with other buildings, Residential steel building has its particularity. Offices and workshops can use a relatively fixed column network, and the storey height is also higher. The space occupied by the beams and columns is suitable for people. The rules of the column network are conducive to the beams. Layout. On the contrary, the residence is a product with many changes. According to the requirements of the building, a regular column network is rarely arranged. The interior space of the house is relatively small and changes a lot, which is not conducive to the layout of the steel frame.

After seeing this and learning so much information about residential steel structures, I believe you must also want to order a Residential steel building. Qingdao Xinguangzheng Steel Structure Co., Ltd. can provide the best Residential steel building you need. At the same time, their after-sales service is also very considerate.

Oz Uk Agricultural Steel Buildings Contact Details Website Telephone Click to view Mobile Click to view Website www.oz-uk/steel-buildings-quick-pick-link/agricultural Contact Mr Chris Peach Email Info@oz-uk Address Unit 8 Bartons Crt, Horsefair Close St John's Business Estate, Downham Market Kings Lynn Norfolk PE38 0QR England UK

Commercial Steel Buildings For Sale – Find Prices, Designs, and Contractors Are you looking to build a new commercial steel building, but don’t know where to start? Find out how much steel buildings cost per square foot, compare types, and more. There are a ...

state-owned steel mills Performance of Steel Buildings 1) Wind Resistance Good rigidity and resistance to deformation make it resistant to 70 m/s hurricanes. 2) Shock Resistance A strong “plate rib structure system” is suitable for areas where the seismic intensity is above 8 …

Our steelwork fabrication facilities feature three no.3 tonne cranes and a combi-lift fork truck with a 4 tonne capability to handle our manufacturing capacity of up to 30 tonnes per week. Further supported by our powerful Voortman Drilling Line which has the capacity to drill up to 12,000mm long beams from as small as 127 x 76 U/B’s up to ...

Trading Company(20456) Manufacturer(18028) Wholesaler(10942) Exporter(8468) Agent(6128) Distributor(5880) Online Seller(5697 ... US industrial metal building/steel construction buildings US

Product Name Prefab House Column Double C80 steel, Thickness 1.8mm, Material Q235 Roof Beam C80 steel, Thickness 1.5mm, Material Q235 Floor Purlin C80 steel, Thickness 1.5mm, Material Q235 Wall Panel Colored-steel sheet EPS sandwich panel/rock

Walls serve the vital purpose of keeping a building up and giving it protection against external weather conditions. At the same time, they also divide spaces within the building. They have multiple purposes and correspondingly varied functional requirements. The most important are: Strength Stability Durability Weather resistance Fire resistance

Source: US Customs and Border Protection: Use for monitoring purposes only. 1 Includes intellectual property rights (IPR), import safety, and other trade violation seizures. IPR seizures encompass goods seized for violating trademark and/or copyright laws and regulations. Import safety seizures encompass products such as toys, pharmaceuticals ...