Chicken Farm- China Manufacturers Factory Suppliers

Commercial steel building is a new type of energy-saving and environmentally-friendly building system. It is known as one of the "green buildings" in the 21st century. It is an energy-saving, environmentally-friendly, and recyclable building structure.

What is the installation and welding process of commercial steel building?

The general sequence of commercial steel building welding is: pre welding inspection → preheating and derusting → installation and welding of base plate and arc striking plate → welding → inspection

1. Before commercial steel building welding, check the groove angle, blunt edge, gap and staggered joint, and remove the rust, oil stain and iron oxide scale in and on both sides of the groove.

2. Preheating. Before commercial steel building welding, gas welding or special baking gun shall be used to heat the groove and the base metal within 100mm on both sides evenly, and the surface thermometer shall be used to measure the temperature to prevent the temperature from meeting the requirements or local oxidation on the surface and preheating temperature.

3. Recheck the preheating temperature. If the temperature is not enough, reheat it to make it meet the requirements.

4. When assembling and welding the backing plate and arc striking plate, the surface cleanliness shall be the same as that of the groove surface, the backing plate shall be close to the base metal, and the arc striking plate shall be firmly welded with the base metal.

What should be paid attention to during the installation and welding of commercial steel building?

1. Welding: the weld bead of the first layer shall seal the connection between the base metal and the backing plate in the groove, and then weld layer by layer until the groove is filled. After each weld is welded, the welding slag and spatter must be removed, and the welding defects shall be ground away and repaired in time.

2. An interface must be welded continuously. If it is necessary to stop welding halfway, it shall be subject to thermal insulation and slow cooling treatment, and shall be heated again according to the regulations before re welding.

3. In case of rain and snow, commercial steel building shall stop welding. There shall be a wind shield and canopy around and above the welded junction of components. When the wind speed is greater than 5m / s, the welding shall be stopped. When the ambient temperature is lower than zero, preheating and post heating measures shall be taken for construction according to regulations.

4. Carbon structural steel shall be subject to weld flaw detection after the weld is cooled to ambient temperature, and low alloy structural steel shall be subject to weld flaw detection 24 hours after completion.

5. Welders and inspectors of commercial steel building shall carefully fill in the operation record form.

What should I pay attention to when purchasing commercial steel building?

When purchasing commercial steel building, we should pay attention to the design of waterproof, heat-insulating and anti-corrosion of the steel structure. The design documents did not specify the steel derusting grade and paint and coating thickness, and did not adopt corresponding measures according to the different fire resistance limits of different parts. commercial steel building of thermal insulation protection measures needs to be avoided.

Commercial steel building has focused on the development and production of commercial steel buildings for several years. And it commits to provide perfect service for every customer from all over the world.

Introduction of Maldives Prefabricated Steel Structure Construction Mall Building Hardware Store:

Project Area: 3323 ㎡       

Project Date: 2017

Project Detail: Six-story steel structures, 100mm fiberglass wool sandwich panel for roof and Glass Curtain +Aluminum Wall Cladding for outer wall and 75mm rock wall sandwich panel as inter wall. The fireproof grade is grade 2, and the fireproof coating is indoor thin fireproof coating.

Effect picture of Maldives Prefabricated Steel Structure Construction Mall Building Hardware Store :

Company information

Qingdao Xinguangzhegn steel structure group company has 1200 workers, 360000 ㎡ non-dust workshop, 25 years experience, CE, ISO9001, ISO9712, ISO3834, BV, SGS certificated, one hour reach Qingdao port, our company, as a manufacture, this is how we keep good quality and competitive prices for global valued customers.

We provide steel building design, farm house design, manufacture and installation service.

Steel building accessories are constructed of steel materials. It is one of the main types of building structures. The structure consists mainly of steel bearings, steel columns, steel joints and other components made of profile steel and steel plates and uses rust removal and rust protection methods such as silylation, pure manganese phosphation, water washing and drying, galvanizing and so on.

How to use Steel building accessories?

Prefabricate and assemble Steel building accessories on the steel platform according to the installation sequence and process requirements to ensure the welding quality.

The spacing between the splicing joint of flange plate and web plate of section steel shall be greater than 200mm. The splicing length of flange plate shall not be less than 2 times of plate width; The web splicing width shall not be less than 300 mm and the length shall not be less than 600 mm.

In order to facilitate welding and ensure welding quality, the stiffener plates, connecting plates, base plates and cantilever beams (beams) on columns and beams shall be assembled and welded on the ground steel platform according to the dimensions of the construction drawing.

The Steel building accessories prefabricated on the steel platform shall not only be fabricated and assembled according to the construction drawings and specifications, but also consider the process of on-site installation and the change of installation size.

Why does Steel building accessories need post-maintenance?

Some Steel building accessories users do not know that steel structures still need to be maintained and maintained. As a result, there is serious corrosion that users often can't find out, which makes steel products appear many unsafe hidden dangers, reduces the safety of Steel building accessories in use, and even affects normal use functions. It is recommended that the design unit not only put forward the painting requirements of the steel structure in the painting design description of the steel structure, but also put forward the maintenance and maintenance requirements of the Steel building accessories according to its use.

How to prevent Steel building accessories from rusting?

There are many ways to prevent Steel building accessories from rusting, and the following are usually used.

 The steel structure is made of alloy steel that is not easy to rust

 Chemical oxide layer protection method

 Using metal coating protection method

 Non-metallic coating protection law

In the later maintenance and maintenance process, non-metallic coating protection method is especially commonly used. The surface of the component is protected by paint and plastic, so that it does not contact the surrounding corrosive medium, so as to achieve the purpose of anti-corrosion. This method has good effect, low price, and has a wide range of paint varieties, a wide range of options, and strong applicability. It is not limited by the shape and size of the component. It can form a film with any shape on the surface of the component. The adhesion is firm. It can also follow the temperature change. The components are telescopic and easy to use. It is also possible to give the component a beautiful color.

Great products begin with the best engineering staff, and Qingdao Xinguangzheng Steel Structure Co., Ltd. is ready to assist you with your technical requirements for Steel building accessories.

Plant Introduction of Sri Lanka Prefabricated Steel Structure Material for Power Plant 

Project Brief Description: Lakvijaya power plant, the largest power plant in Sri Lanka, is the company that undertakes the steel structure materials of wind barrier project. Designed and fabricated by Qingdao Xinguangzheng Steel Structure Co., Ltd. in 2019.

Qingdao Xinguangzheng steel structure Group is a public company with 1200 workers, 360000 ㎡ non-dust workshop, 25 years experience, CE, ISO9001, ISO9712, ISO3834, BV, SGS certificated, one hour reach Qingdao port, our company, as a manufacture, this is how we keep good quality and competitive prices for global valued customers.

We provide steel building design, farm house design, manufacture and installation service.

Commercial steel building, the preferred steel and metal building in construction, has quickly become the first choice for residential and commercial building safety. Here we are going to talk more about the Commercial steel building !

• What are the advantages of Commercial steel building?

• Why do more and more people choose Commercial steel building?

• What are the advantages of Commercial steel building?

What are the advantages of Commercial steel building?

In this field of commercial construction, Commercial steel building has greatly exceeded the normal construction capabilities of its competitors.

Because Commercial steel building has a quality guarantee of up to 40 years, the steel structure of the building is durable.

For the daily maintenance of wall panels, roofs and metal buildings, steel structure owners may pay a huge price for this, because steel structure houses are more resistant to wear and tear than other materials every day.

Commercial steel building is safe in extreme weather. When your country/region is under extreme climatic conditions, such as earthquakes, tornadoes, ice storms, or just a strong thunderstorm, this Commercial steel building is proven to be more resistant than others because it is made of steel .

Why do more and more people choose Commercial steel building?

Because of this, government agencies and municipalities always choose Commercial steel building to protect their most important property from severe weather.

Because of this, more and more residential customers choose to use steel to build their houses for maximum protection.

With a steel structure, you can have many advantages, such as economy, beauty and reliability.

In addition to these eye-catching features, Commercial steel building also has great flexibility for customers who want to configure ideal buildings to meet their precise requirements and satisfy their aesthetics.

Compared with other buildings, customized Commercial steel buildings and residences provide users with more versatility, and metal buildings are also a very economical choice for new buildings.

What are the advantages of Commercial steel building?

The steel structure of Commercial steel building has a series of advantages, such as high strength, light weight, good seismic performance, high degree of industrialization, fast construction speed, small floor area and so on. Steel has good mechanical processing performance, which is most easy to realize modular, standardized, industrialized, assembled and mechanized production of buildings, realize no fire, no water, no dust and no garbage on the construction site, have good recycling of steel, and most easy to realize the concept of full-life green building. Due to the strong plasticity of steel structure, it can be widely used in civil buildings, public buildings and commercial buildings. Such fields as industrial plants, low rise, multi-storey and super high-rise buildings, civil residences, large public buildings, terminal buildings, thermal power plants and boiler steel frames, highway and railway bridges and offshore oil platforms.

Qingdao Xinguangzheng Steel Structure Co., Ltd. is a Commercial steel building manufacturer established for more than several years. Please consult our company for details through https://www.steelstructureonline.com/! Customer requirements are our pursuit.

Prefab House is a house constructed by industrialized production methods. It is a house constructed by prefabricating part or all of the components of the house in the factory and then transporting it to the construction site. The components are assembled through reliable connections.

• What are the characteristics of Prefab House?

• What are the actual advantages of Prefab House?

• What is the significance of the appearance of Steel Structure Prefab House?

What are the characteristics of the Prefab House?

1. Prefab House is estimated to be about 30% faster than conventional construction methods.

2. The safety of the Prefab House is perfectly fine, since the finished steps, external walls etc. are transported to the construction site but also have to be covered instead of easy connection with steel concrete. Steel rods run through each floor, and the structure of the house is very strong.

3. Compared to traditional built houses, Prefab House has a higher component precision that can minimise frequent quality problems such as wall friction and leakage and can improve the general level of safety, fire resistance and durability of the house. It uses a light partition system and the owner can change the decoration as needed.

4. Prefab House is more energy-saving and environmentally friendly when used in the home, e.g. a new type of thermal insulation layer that has a better thermal insulation effect. When a household measurement is implemented and the heating has the same temperature, the room temperature of the "assembled" space is higher. The head of household may consider lowering the heating temperature, saving heating costs and, at the same time, reducing energy consumption.

What are the actual advantages of Prefab House?

1. The space layout of Prefab House is flexible.

2. The construction process of Prefab House is environmentally friendly and sustainable.

3. The structure of Prefab House has light weight and high bearing capacity.

4. Prefab House has excellent quality and superior seismic performance.

5. Prefab House can realize the industrialization and industrialization of residential construction, and the construction period is short.

6. Prefab House is very economical and applicable.

What is the significance of the appearance of Steel Structure Prefab House?

For a long time, the construction of houses is dominated by concrete structures. Concrete structure houses mainly use on-site manual wet work. There are problems such as low production efficiency, long construction period, high energy consumption, serious pollution, difficult to guarantee quality and performance, and short life cycle. Around the 1990s, the development of steel structures began. The appearance of Steel Structure Prefab House is a major contribution to our human habitation, reducing the pressure on the living environment. Over the years, housing construction data show that the amount of construction waste has accounted for nearly 40% of the total urban waste.

Qingdao Xinguangzheng Steel Structure Co., Ltd., which has been established for over ten years, focuses on the production of Prefab Houses. Here, you can find the Prefab Houses you need.

Industrial steel building mainly means that the main load-bearing components are composed of steel. Including steel pillars, steel beams, steel structure foundations, steel roof trusses (of course, the span of the factory building is relatively large, and it is basically steel structure roof trusses now), steel roof, note that steel structure walls can also be surrounded by brick walls.

• What are the characteristics of Industrial steel building?

• What are the industrial characteristics of Industrial steel building?

• Why do we have to carry out daily maintenance on Industrial steel buildings?

What are the characteristics of Industrial steel building?

The characteristics of the steel construction workshop are:

1. Industrial steel building is light, high-strength and has a large span width.

2.The construction time of industrial steelworks is short, reducing investment costs accordingly.

3. Industrial steel buildings have poor fire resistance and corrosion resistance and steel structures should not be used in areas with low temperatures.

4. Industrial steel building is easy to move and recycle without contamination.

What are the industrial characteristics of Industrial steel building?

Impact

The roofs of flat buildings are mostly inclined roofs, so that the roof construction essentially uses a triangular roof chair system made of cold-formed steel components. The light steel components form a very strong structure after sealing the building plates and plasterboard plates. "Plate-rib structural system", the industrial steel structure of this structure has a stronger earthquake resistance and resistance to horizontal loads and is suitable for areas with earthquake intensities above 8-degree.

Air resistance

The Industrial steel building has a low weight, a high strength, a good overall stiffness and a strong deformability. The building weighs only a fifth of the brick concrete construction and holds a hurricane of 70 meters per second so that life and property can be effectively protected.

Durability

The housing structure of the Industrial steel building consists entirely of cold-formed thin-walled steel component systems. The steel frame consists of a high-strength, cold-rolled, fire-soaked super-corrosion protection sheet which effectively avoids the influence of steel sheet corrosion during construction and use and increases the durability of light steel components. The durability of the structure can reach 100 years.

Why do we have to carry out daily maintenance on Industrial steel buildings?

Industrial steel buildings must be regularly cleaned and maintained. Under normal circumstances, it must be inspected and maintained once a year. When cleaning the outer wall of the Industrial steel building, you must be careful not to contaminate anything. Do not use steel wire balls, brushes and other abrasive cleaning agents. If you use clean water, you should rinse from top to bottom. The branches, leaves and similar objects on the Industrial steel building should be cleaned in time to avoid unnecessary problems due to the delay. If the surface of the metal plate for industrial steelmaking is damaged, it should be repaired in time to prevent the surface of the metal plate from corroding by sun and rain. If necessary, use all coated high-elastic nanomaterials to protect the metal roof plate, act effectively in thermal insulation and sealing and save energy for room climate.

Seeing this, do you also want to order a Industrial steel building? If necessary, you can contact Qingdao Xinguangzheng Steel Structure Co., Ltd. they will provide the Industrial steel building of the best quality.

Residential steel building is a residential system composed of an envelope structure and a steel supporting structure. It is a new type of energy-saving and land-saving residential system. Its steel structure residence abandoned solid clay bricks and effectively used land resources. Compared with traditional houses, steel structure houses have advantages in terms of use function, design, construction and comprehensive economy.

• What are the reasons why people choose Residential steel building?

• What should the choice of Residential steel building structural system look like?

• What is the framework system used by Residential steel building?

What are the reasons why people choose Residential steel building?

1. Residential steel building energy saving and environmental protection

The main body of the Residential steel building is steel components, and the wall material is thermal insulation mortar, which not only meets the requirements for energy saving, but also can be recycled. It is a green and environmentally friendly recycling building that meets the requirements of sustainable development. The thermal resistance can reach a brick wall thickness of about 1m. At present, the global population is large and energy consumption is large, and the promotion and application of steel structure housing is the final choice.

2. Residential steel building's pipe network line layout is convenient

In residential buildings, there are many lines of professional plumbing and electricity pipe network, which will reduce the effective use area in traditional buildings. In Residential steel building, there are many holes or holes in beams and columns, which is easy to form a cavity for wiring layout. Moreover, the beam can be artificially made into a honeycomb shape, which is convenient for line layout, which not only saves the net height of the building, but also increases the use area.

What should the choice of Residential steel building structural system look like?

According to engineering practice, the commonly used Residential steel building structure system can be selected with reference to the following scope:

The 4th to 6th floors are the steel frame system, the steel frame-support system, and the steel frame-shear wall system; the 7th to 12th floors are the steel frame-concrete core tube (shear wall) system.

The section form of steel components should be hot-rolled H-section steel, high-frequency welded H-section steel and steel tube concrete.

What is the framework system used by Residential steel building?

Light steel frame system

The light steel frame system is a load-bearing frame composed of hot-rolled H-shaped steel (or I-beam), high-frequency welded H-shaped and cold-formed square pipes, and a steel structure residence with composite curtain walls or infill walls as the enclosure structure system.

The wall panels in the picture collection are made in the factory with fly ash as the filler, sulfoaluminate as the cement, polystyrene foam (EPS) as the core material, and glass fiber mesh as the reinforcement material. A lightweight board. Special adhesive is used to bond the plate and the light steel frame, and between the plate and the plate. To prevent thermal bridges using double-layer plates.

Qingdao Xinguangzheng Steel Structure Co., Ltd., as a leading company in China's Residential steel building, has committed to providing the most suitable Residential steel building at a reasonable price, and whatever it takes to satisfy the customer’s needs.

ACG released Indian Commercial Vehicle Market Report 2022 and Outlook. The Indian Commercial Vehicle sales done in 2021 are 0.67 million units compared to slightly more than half a million in CY 2020. The year 2020 was completely hit by the pandemic. Indian CV had hit the rock bottom owing to the COVID-19. Surprisingly, the year that followed ...

Royal Canadian Steel Inc. Since its establishment in 1990, Royal Canadian Steel has become one of the leading steel service and steel export centers in Canada and United States. Our products include Secondary and Excess Prime Steel: Stainless Steel, Cold Rolled Steel, Galvanized Steel and other types of steel products.

JSW Steel Ltd Steel Authority of India Ltd Rashtriya Ispat Nigam Ltd Jindal Steel and Power Ltd Bhushan Power and Steel Ltd ArcelorMittal Nippon Steel Ltd Tata Steel Ltd Tata Steel BSL Ltd Affiliate Members ESL Steel Ltd Arjas Steel Pvt Ltd Institute for Steel Development and Growth-INSDAG Jindal Stainless

Welcome to Steel Office Furniture. We specialize in Steel Cabinets, Steel Drawers, Shelving Units, Canteen Tables, Lockers, Fire Resistant Cabinets and Drawers and much more. Learn More Cabinets

Viking Steel Structures specializes in custom steel buildings for various industries, including commercial, industrial, agricultural, and recreational applications. Our custom buildings are professionally crafted to fit your specifications and provide significant value. 30x41 Utility Carport Building Starting Price:

About metals4U. Welcome to metals4U, the biggest online metal supplier in the UK. Whether you are a keen hobbyist, tradesperson or contractor, we are the best store to help you find all the materials and tools you need. There is no limit to what you can create, and we are proud to stock a varied, great quality product range to help you along ...

Our Metal Warehouses are Built to Last with Vertical Roofs Our steel warehouses are superior when it comes to the ultimate support and strength to hold up during all the elements. We use the strongest roof design that is guaranteed to meet and even exceed most building codes for snow and wind loads.

The steel frame structure system refers to a frame structure composed of steel beams and steel columns along with the longitudinal and transverse directions of the buildings. The steel beams and steel columns form the structural system that bears and resists lateral forces. 1. There are three forms of a rigid connection between beam and column.