Arab Steel Warehouse Quote- China Factory Suppliers Manufacturers

Commercial steel building is a new type of energy-saving and environmentally-friendly building system. It is known as one of the "green buildings" in the 21st century. It is an energy-saving, environmentally-friendly, and recyclable building structure.

What is the installation and welding process of commercial steel building?

The general sequence of commercial steel building welding is: pre welding inspection → preheating and derusting → installation and welding of base plate and arc striking plate → welding → inspection

1. Before commercial steel building welding, check the groove angle, blunt edge, gap and staggered joint, and remove the rust, oil stain and iron oxide scale in and on both sides of the groove.

2. Preheating. Before commercial steel building welding, gas welding or special baking gun shall be used to heat the groove and the base metal within 100mm on both sides evenly, and the surface thermometer shall be used to measure the temperature to prevent the temperature from meeting the requirements or local oxidation on the surface and preheating temperature.

3. Recheck the preheating temperature. If the temperature is not enough, reheat it to make it meet the requirements.

4. When assembling and welding the backing plate and arc striking plate, the surface cleanliness shall be the same as that of the groove surface, the backing plate shall be close to the base metal, and the arc striking plate shall be firmly welded with the base metal.

What should be paid attention to during the installation and welding of commercial steel building?

1. Welding: the weld bead of the first layer shall seal the connection between the base metal and the backing plate in the groove, and then weld layer by layer until the groove is filled. After each weld is welded, the welding slag and spatter must be removed, and the welding defects shall be ground away and repaired in time.

2. An interface must be welded continuously. If it is necessary to stop welding halfway, it shall be subject to thermal insulation and slow cooling treatment, and shall be heated again according to the regulations before re welding.

3. In case of rain and snow, commercial steel building shall stop welding. There shall be a wind shield and canopy around and above the welded junction of components. When the wind speed is greater than 5m / s, the welding shall be stopped. When the ambient temperature is lower than zero, preheating and post heating measures shall be taken for construction according to regulations.

4. Carbon structural steel shall be subject to weld flaw detection after the weld is cooled to ambient temperature, and low alloy structural steel shall be subject to weld flaw detection 24 hours after completion.

5. Welders and inspectors of commercial steel building shall carefully fill in the operation record form.

What should I pay attention to when purchasing commercial steel building?

When purchasing commercial steel building, we should pay attention to the design of waterproof, heat-insulating and anti-corrosion of the steel structure. The design documents did not specify the steel derusting grade and paint and coating thickness, and did not adopt corresponding measures according to the different fire resistance limits of different parts. commercial steel building of thermal insulation protection measures needs to be avoided.

Commercial steel building has focused on the development and production of commercial steel buildings for several years. And it commits to provide perfect service for every customer from all over the world.

Introduction of Zhongjie era Steel Structure Frame Overpass Project 

Zhongjie Times Square overpass project is the first Cross Street overpass project in Pingdu. The whole project is composed of three overpasses. The length of the straight overpass on the east side is 56.3 meters and the width is 5 meters. The length of the straight overpass on the west side is 49 meters and the width is 5 meters. The diameter of the main bridge surface of the central circular overpass is 56 meters. The narrowest part is 6.5 meters and the maximum width is 12 meters. The construction of the overpass on Hongqi Road can avoid the interference of people and vehicles To improve the road capacity, and effectively solve the problem of efficiency and safety of a large number of people crossing the street.

After completion, it will become the most characteristic commercial block with urban flavor in the main urban area of Pingdu City, as well as the landscape landmark and cultural landmark of Pingdu.

Prefab House is a house constructed by industrialized production methods. It is a house constructed by prefabricating part or all of the components of the house in the factory and then transporting it to the construction site. The components are assembled through reliable connections.

• What are the characteristics of Prefab House?

• What are the actual advantages of Prefab House?

• What is the significance of the appearance of Steel Structure Prefab House?

What are the characteristics of the Prefab House?

1. Prefab House is estimated to be about 30% faster than conventional construction methods.

2. The safety of the Prefab House is perfectly fine, since the finished steps, external walls etc. are transported to the construction site but also have to be covered instead of easy connection with steel concrete. Steel rods run through each floor, and the structure of the house is very strong.

3. Compared to traditional built houses, Prefab House has a higher component precision that can minimise frequent quality problems such as wall friction and leakage and can improve the general level of safety, fire resistance and durability of the house. It uses a light partition system and the owner can change the decoration as needed.

4. Prefab House is more energy-saving and environmentally friendly when used in the home, e.g. a new type of thermal insulation layer that has a better thermal insulation effect. When a household measurement is implemented and the heating has the same temperature, the room temperature of the "assembled" space is higher. The head of household may consider lowering the heating temperature, saving heating costs and, at the same time, reducing energy consumption.

What are the actual advantages of Prefab House?

1. The space layout of Prefab House is flexible.

2. The construction process of Prefab House is environmentally friendly and sustainable.

3. The structure of Prefab House has light weight and high bearing capacity.

4. Prefab House has excellent quality and superior seismic performance.

5. Prefab House can realize the industrialization and industrialization of residential construction, and the construction period is short.

6. Prefab House is very economical and applicable.

What is the significance of the appearance of Steel Structure Prefab House?

For a long time, the construction of houses is dominated by concrete structures. Concrete structure houses mainly use on-site manual wet work. There are problems such as low production efficiency, long construction period, high energy consumption, serious pollution, difficult to guarantee quality and performance, and short life cycle. Around the 1990s, the development of steel structures began. The appearance of Steel Structure Prefab House is a major contribution to our human habitation, reducing the pressure on the living environment. Over the years, housing construction data show that the amount of construction waste has accounted for nearly 40% of the total urban waste.

Qingdao Xinguangzheng Steel Structure Co., Ltd., which has been established for over ten years, focuses on the production of Prefab Houses. Here, you can find the Prefab Houses you need.

Generally speaking, the installation procedures of industrial steel building include installation of steel columns, installation of inter-column supports, temporary installation of steel crane beams, roof beams, roof supports, steel crane beams, etc., correction, fixation, and structural installation of maintenance.

• What is the specific process of industrial steel building construction?

• How to regularly maintain industrial steel building?

• How to consider the cost of industrial steel building construction?

What is the specific process of industrial steel buildings?

1. Lifting the main structure of industrial steel buildings: connecting steel carriers on the ground, erecting steel columns, lifting steel carriers, connecting secondary structures, correcting the deviation of the main structure, installing crane carriers (optional), lifting intermediate layers (optional), and coating with fire resistant paint pack.

Main control quality: The deviation of the main structure should meet the specifications and design requirements and the initial and final application of high-strength screws should meet the requirements.

2. Installation of secondary structure: roofing posts, roof wall supports, flange supports, etc.

3. Laying of roof plate and insulation layer: first lay insulation layer, then assemble roof plate (in some projects a position of steel fabric is also placed under the insulation layer to prevent a fall of the insulation layer, this mainly depends on insulation layer level)

Main quality control: The roof is mainly waterproof, therefore the plate should be covered with the plate, the nail position, the glue coating should be full or not, the glue should be wiped clean and the coating on the surface of the plate should not be damaged to rust etc. to avoid.

How to regularly maintain industrial steel building?

industrial steel building wall maintenance and installation: mainly the installation of wall insulation and wall panels.

The main quality control of industrial steel building: the wall is mainly an aesthetic problem, and a window area is waterproof. There is also the problem of installation deviation. For example, the bottom should be flat, the entire plane should be flat, the flatness deviation between the board and the board should meet the requirements, and so on.

The detailed structure of the industrial steel building: mainly the installation of some trims, such as the wrap angle between the roof and the wall, the wrap angle at the corner of the wall, the flooding board between the wall panel and the brick wall, the door and window trim, etc.

How to consider the cost of industrial steel building construction?

The price of industrial steel building can only be compared with certain basic conditions, such as whether it is imported or domestic color panels, its thickness, coating; insulation material and thickness; whether there is a skylight; workshop bays and spans; whether there are cranes, crane tonnage, Many factors such as the level of the work system are related, and the impact of the price difference in other regions and the qualification level of the construction unit cannot be ignored.

The industrial steel building has achieved an irreplaceable position in industrial production. Qingdao Xinguangzheng Steel Structure Co., Ltd. is committed to providing different kinds industrial steel buildings of high quality for all customers from all over the world.

Prefab house is a structure mainly made of steel, which is one of the main building structure types. The characteristics of steel are high strength, light weight, and high rigidity, so it is especially suitable for the construction of large-span, super-high and super-heavy buildings.

• Compared with traditional concrete buildings, what are the advantages of Prefab house?

• What are the advantages of Prefab house?

• What is the installation process of Prefab house?

Compared with traditional concrete buildings, what are the advantages of Prefab house?

Compared with prefabricated concrete buildings, Prefab houses have the following advantages:

1. There is no on-site cast-in-place node, the installation speed is faster, and the construction quality is easier to be guaranteed;

2. The steel structure is a ductile material with better seismic performance;

3. Compared with concrete structure, steel structure has lighter weight and lower foundation cost;

4. The steel structure is a recyclable material, which is more green and environmentally friendly;

5. Well-designed steel structure prefabricated buildings are more economical than prefabricated concrete buildings.

6. The cross-section of beams and columns is smaller, and more usable area can be obtained.

What are the advantages of Prefab house?

Save heating costs

Prefab house is more energy-efficient and environmentally friendly when used in the home, such as a new type of thermal insulation layer that has a better thermal insulation effect. When a household measurement is implemented and the heating has the same temperature, the room temperature of the "assembled" space is higher. The head of household may consider lowering the heating temperature, saving heating costs and, at the same time, reducing energy consumption.

Save energy

Finished house is of great benefit for energy saving and environmental protection. Through factory production and on-site assembly, it can significantly reduce building protection and waste water, reduce building noise, reduce harmful gas and dust emissions and reduce building and management personnel on site.

What is the installation process of Prefab house?

The assembly procedure for the steel construction of the Prefab house: steel column assembly -Installation of the supports between the columns -temporary installation of the steel bearer -roof bearings, roof bearings -correction and fixing of the steel bearer -Installation of the maintenance structure.

1. Contamination protection: Avoid rain water entering the metal roof from the outside. Rainwater enters the metal roof mainly through overlapping joints or knots. In order to achieve the function of the centrifuge, it is necessary to use a sealing disc at the screw connection and to make a concealed fixation. Use sealants or welds on the top of the plate. Best use a long board to remove the overlap. Close water-tight treatment for bleeding.

2. Moisture resistant: Avoid condensation of water vapour in the soil and metal wax layer and drain the water vapour in the metal wax layer. The solution is to fill the metal roof with thermal insulation cotton, place a waterproof membrane on the metal floor plate and have ventilated knots on the metal roof.

3. Daylight: Improve indoor lighting during the day by means of skylights and save energy. When installing daylight panels or daylight glass at certain points on the metal roof, the duration of use of the daylight should be aligned with the metal ceiling panel and the connection between the daylight and the metal ceiling panel should be treated watertight.

Seeing this, do you also want to order an Prefab House? If necessary, you can contact Qingdao Xinguangzheng Steel Structure Co., Ltd. they will provide the Prefab House of the best quality.

Prefab House refers to the use of industrial production methods to build houses, that is, the stairs, exterior walls, balconies, air-conditioning panels, etc. of the house are all prefabricated in the factory outside the construction site, and then shipped to the construction site for "assembly", and the interior of the house will be refined at one time. Handed over after renovation. That is, the huge external walls, stairs, and balconies from the factory are "assembled" on the construction site into houses and buildings.

• What are the advantages of a Prefab House?

• What are the structural types of Prefab Houses?

• What should we be careful about when selecting a Prefab House?

What are the advantages of a Prefab House?

1. Safe and reliable

The Prefab House with steel as the main building material has a high capacity per volume unit, is more stable and solid than the traditional brick and brick concrete technology, has a better seismic performance, wind resistance, water density and refractory performance and also has thermal insulation and sound protection functions. Steel has good ductility and can better use the energy brought in by earthquakes, so it has good seismic performance and a high structural security t hat guarantees the safety of stay.

2. Easy construction and short construction time

All components are prefabricated in the factory and only have to be installed on site, which greatly shortens the construction cycle. A 6000-square-metre-long building can basically be installed in 40 days.

What are the structural types of Prefab Houses?

1. Structural system

The structure of the Prefab House can be divided into: steel frame system, steel frame support system, steel frame-core tube system, steel frame-module-core tube system and steel frame-shear-wall system. With the continuous development of the technology, newer steel construction systems will also appear.

2. Peripheral protection system

The outer protective system of the Prefab House can be divided into blocks, plates, cans and other types.

3. Internal system

Traditional construction has many disadvantages. For example, the traditional rough decoration method does not separate the interior system and the structural system, which makes it difficult to adapt to the modern development of the housing industry; the house technology lines are not separated and the water and power lines are buried in the support layer, which the "century residence" cannot realize." The waste of social resources is serious.

What should we be careful about when selecting a Prefab House?

1.The costs are relatively higher than in the traditional Prefab House made of brick concrete and concrete.

2. The steel structure of the Prefab House, with its unique steel structure, walls, roofs and other materials, as well as the standardized and final internal distribution and support facilities, is difficult to adapt to the habits of people "arbitrarily handling the house".

3. Corrosion of steel: Al-galvanized steel must be used for maximum corrosion protection and the main steel structure can reach fifty years.

4. There are many requirements for new materials. The structure of steel houses is equipped with materials such as thermal insulation and heat protection, usually using new lightweight materials.

Prefab Houses produced by Qingdao Xinguangzheng Steel Structure Co., Ltd. feature attractive appearance, excellent performance, user-friendly operation, easy maintenance, and internationally advanced performance indicators, and are exported to more than 10 countries and regions.

The full name of MDC is"MONDU DA CASA (home world)", which is constructed by Qingdao Xinguang Zheng Steel Structure Co., Ltd. This is a comprehensive shopping center centering on the theme of "happy home". This theme is the same as the enterprise mission of "benefiting the society, achieving employees and making customers happier". In addition to "home world", she has another interpretation of "modern decoration Center".

MDC is located in KIKUXI section of Luanda expressway, surrounded by Angola national stadium, high-end residential villa area, Brazil nursery garden, and Luanda commercial pedestrian street under planning, with superior geographical environment and convenient transportation.

"MDC home world" shopping center covers an area of about 30000 square meters. Relying on the global procurement network, it has gathered kipor generator 4S shop, furniture store, building materials store, home furnishing store and home appliance store. The categories include building materials pipe fittings, wood, floor tiles, paint and coating, decorative lamps, kitchen and bathroom equipment, hardware tools, electrical and electrical materials, gardening supplies, cloth furniture, home appliances, etc., and also auxiliary It is one of the most comprehensive "one-stop purchasing" centers for home furnishings in Luanda with public service facilities such as business office, catering, leisure and entertainment, bank, etc.

Project Introduction:

Solomon office project is a two-story frame structure, with a building area of more than 1500 square meters. The first floor is maintained as aluminum-plastic plate curtain wall and part of glass curtain wall, the second floor is maintained as glass curtain wall, the roof is glass wool composite plate, and the parapet part is aluminum-plastic plate.

 

Personnel involved in design and construction refinement: Liu Kangning, Jing Yanyan

Total project amount: 2.94 million

 

Detailed address: Honiara, Solomon Islands

The following project related parameters:

Area: 1500 square meters

Eave height: 7M

Ridge height: 8M

Number of floors: two

Wind speed: 176km / h

Load: second floor load: 450kg / m2, roof: 30kg / m2

Shapes: Framing

Steel consumption: 90 tons

Purpose: Salomon Telekom office and warehouse

 

 

Detail of Prefabricated Steel Structure Building Office in Solomon

 

Main Characters of prefab steel warehouse

· Super Aseismatic

Most part of the structure will be consisted of cold formed steel members, this system aseismatic grade can reachto 8.

· Wind Resistance

Steel structure building has the performance of high strength, solid rigidity and good deformation capacity, can resist strong wind for 50m/s.

·Durable

The steel material will be painted or galvanized as customers' requirement to be more anticorrosion and rustproof, the lifespan of the structure can be reach to 50~70 years.

·Heat Insulation

Sandwich panel can improve the insulation performance of the building, effectively avoid the phenomenon of "cold bridge" wall

·Environment Protection

Little waste for pollution in construction, 100% steel structure materials can be recycled, most of other related materials also can be recycled.

·Easy and Fast Build

Dry construction, will not influenced by the weather and environment, save much time and labor cost. One 300m2 steel structure building, can be finished in 30 days by only 5 workers.

United States Steel Corporation Corporate Headquarters 600 Grant Street Pittsburgh, PA 15219 For general inquiries, contact the U. S. Steel Operator. Phone: (412) 433-1121 8 a.m. - 5 p.m. Eastern Monday - Friday Twitter Linked In Instagram ...

About Us Weifang Tailai Steel Structure Engineering Co., Ltd was established in 2003. we are one of the strongest steel structure manufacturer in Weifang ,Shandong, China. 2022

Agricultural Steel Buildings Good quality comes 1st; assistance is foremost; business enterprise is cooperation" is our business enterprise philosophy which is regularly observed and pursued by our company for Agricultural Steel Buildings, Chinese Container Homes , Folding House Manufacturers , Mobile Prefabricated Shipping Container House , Two Story 40ft …

Vinod Stainless Steel Thali / Plate Start from Rs.675.00 Buy Now Vinod Stainless Steel Bowls / Vati Start from Rs.409.00 Buy Now Vinod Stainless Steel Glasses Start from Rs.610.00 Buy Now Jug Start from Rs.967.00 Buy Now Hot Casserole Start from Rs.934.00 Buy Now Serving Dish Start from Rs.284.00 Buy Now Thali Set Start from Rs.810.00 Buy Now

28/12/2018· For this selection of a custom-made structure, it is important that you correctly assess all the loads that the various parts of the building will have to cater for, so that the structural engineers can suggest you a design of a structure essentially made up of columns, beams and other elements that are needed to complete the desired structure.

Pre Engineered Structural Steel Factory Buildings, Find Details and Price about Factory Hangar Structural Steel from Pre Engineered Structural Steel Factory Buildings - Qingdao Xinguangzheng Sino Building Co., Ltd For Buyer Search Products

10x15 Mercia Absco Utility Metal Workshop in Zinc ONLY￡1,229.99 Shop Now 20x10 Mercia Absco Metal Utility Workshop in Pale Eucalyptus ONLY￡1,274.00 Email me when instock 10x15 Mercia Absco Utility Workshop in Pale Eucalyptus ONLY￡1,299.99 Email me when instock 10x15 Lotus Metal Workshop Shed in Anthracite Grey ONLY￡1,387.00 COLOURS Shop Now

High Quality Sheds Storage Ready Made House in India Prefabricated Outdoor Sandwich Panel Houses Steel Structure Modern CN;SHN