Arab Steel Structure factory wholesale- Suppliers Manufacturers Factory From China

Introduction of Project:

 

Project address: Davao

Size: 123m * 16m * 2.5m

Detailed parameters: the beams and columns are H-shaped steel, the roof and wall are compounded with 0.4mm veneer + 75 thick glass wool quilt + 0.4mm veneer, and the side wall is insulated door (EPS composite board). The steel structure chicken house adopts the automatic breeding and cleaning system, with a height of 500mm from the ground, and the plastic floor is paved on it to ensure the cleanliness of the chicken house. At present, the survival rate of chickens is 99%.

1.Material of cage and frame is hot dip galvanized steel. The zinc thickness is 275g/m². The life span can reach 15-20 years.

2.The reasonable design of the feeding regulator ensures the regulator move stably, and the birds will not run away and get stuck.

3.Small water cup, feed trough and plastic net are equipped for day old birds.

Agricultural steel building is a construction of steel materials and is one of the main types of construction. The structure consists mainly of steel bearings, steel columns, steel works and other components made of profile steel and steel plates and uses silanisation, pure manganese phosphation, washing and drying, galvanising and other rust and rust protection methods.

• What is agricultural steel building?

• What are the characteristics of people who opt for agricultural steel building?

• What are the benefits of people opting for agricultural steel building?

What is agricultural steel building?

The agricultural steel building is characterized by high strength, low weight, good overall stiffness and high deformation resistance. It is therefore particularly suitable for the construction of large-scale and ultra-high agricultural buildings; The material has a good homogeneity and isotrope, which is ideal for elasticity. The structure most closely corresponds to the basic assumptions of general technical mechanics; the material has good plasticity and toughness, can exhibit large deformations and can withstand dynamic loads well; construction time is short; the agricultural steel industry has a high degree of industrialisation and can be specialised in agricultural production.

What are the characteristics of people who opt for agricultural steel building?

1. agricultural steel building has good sealing performance

Since the welding design can be completely sealed, it can be air and water-tight to high pressure containers, large oil reservoirs, pressure pipes, etc. to be processed.

2. agricultural steel building is heat resistant and non-fire resistant

If the temperature is below 150oC, the properties of the steel change slightly. The steel structure is therefore suitable for hot workshops, but if the surface is exposed to heat radiation of approximately 150, it should be protected by a thermal insulation plate. If the temperature is between 300-C and 400-C, the strength and elasticity module of the steel material decreases significantly, and if the temperature is approximately 600-oC, the strength of the steel material is zero. In buildings with special fire protection requirements, the steel structure must be protected by refractory materials to improve fire resistance.

3. agricultural steel building has poor corrosion resistance

Especially in the vicinity of moist and corrosive media, it rust easily. In general, steel structures must be rusted, galvanized or painted and regularly maintained. Specific measures such as zinc-blockanode protection are required for offshore platform construction in seawater to protect corrosion.

4.The demolition of agricultural steelworks is not subject to any building protection and the steel can be recycled and reused.

What are the benefits of people opting for agricultural steel building?

The grid structure of the agricultural steel building has an adequate load, a high stiffness, a low weight, individual rods and a comfortable production and installation. In recent years, it has often been used in public and industrial buildings with large stretches and large columns. In the construction of agricultural steel buildings there are stainless steel sandwich plates, profile plates, lighting materials and other roof materials. It can be used not only for roof constructions, but also for floors, walls and special constructions.

Agricultural steel production plays an essential role in the current industrial production process. Qingdao Xinguangzheng Steel Structure Co., Ltd. has undertaken to offer the most suitable agricultural steel buildings at a reasonable price.

Prefab house is a structure mainly made of steel, which is one of the main building structure types. The characteristics of steel are high strength, light weight, and high rigidity, so it is especially suitable for the construction of large-span, super-high and super-heavy buildings.

• Compared with traditional concrete buildings, what are the advantages of Prefab house?

• What are the advantages of Prefab house?

• What is the installation process of Prefab house?

Compared with traditional concrete buildings, what are the advantages of Prefab house?

Compared with prefabricated concrete buildings, Prefab houses have the following advantages:

1. There is no on-site cast-in-place node, the installation speed is faster, and the construction quality is easier to be guaranteed;

2. The steel structure is a ductile material with better seismic performance;

3. Compared with concrete structure, steel structure has lighter weight and lower foundation cost;

4. The steel structure is a recyclable material, which is more green and environmentally friendly;

5. Well-designed steel structure prefabricated buildings are more economical than prefabricated concrete buildings.

6. The cross-section of beams and columns is smaller, and more usable area can be obtained.

What are the advantages of Prefab house?

Save heating costs

Prefab house is more energy-efficient and environmentally friendly when used in the home, such as a new type of thermal insulation layer that has a better thermal insulation effect. When a household measurement is implemented and the heating has the same temperature, the room temperature of the "assembled" space is higher. The head of household may consider lowering the heating temperature, saving heating costs and, at the same time, reducing energy consumption.

Save energy

Finished house is of great benefit for energy saving and environmental protection. Through factory production and on-site assembly, it can significantly reduce building protection and waste water, reduce building noise, reduce harmful gas and dust emissions and reduce building and management personnel on site.

What is the installation process of Prefab house?

The assembly procedure for the steel construction of the Prefab house: steel column assembly -Installation of the supports between the columns -temporary installation of the steel bearer -roof bearings, roof bearings -correction and fixing of the steel bearer -Installation of the maintenance structure.

1. Contamination protection: Avoid rain water entering the metal roof from the outside. Rainwater enters the metal roof mainly through overlapping joints or knots. In order to achieve the function of the centrifuge, it is necessary to use a sealing disc at the screw connection and to make a concealed fixation. Use sealants or welds on the top of the plate. Best use a long board to remove the overlap. Close water-tight treatment for bleeding.

2. Moisture resistant: Avoid condensation of water vapour in the soil and metal wax layer and drain the water vapour in the metal wax layer. The solution is to fill the metal roof with thermal insulation cotton, place a waterproof membrane on the metal floor plate and have ventilated knots on the metal roof.

3. Daylight: Improve indoor lighting during the day by means of skylights and save energy. When installing daylight panels or daylight glass at certain points on the metal roof, the duration of use of the daylight should be aligned with the metal ceiling panel and the connection between the daylight and the metal ceiling panel should be treated watertight.

Seeing this, do you also want to order an Prefab House? If necessary, you can contact Qingdao Xinguangzheng Steel Structure Co., Ltd. they will provide the Prefab House of the best quality.

Step 1: Cutting

Cut steel plate into pieces and connections by flame cutting machines (CNC, Semi-automatic flame cutting machines). Long strips will be used as web and flange plate, connections will be used as connected, reinforced or stiffening plate.

 

Step 2: Assembly

Combine web and flange plate together through H-beams assembly machine, make tack welding. Keep the web plate in the middle line, do not be off the center line.

 

Step 3: Gantry automatic submerged arc welding

Make welding by gantry submerged arc welding machine. Make sure the welding sequence and reduce the welding deformation.

 

Step 4: Flange plate of straightening

Start straightening on welding-finished H steel beams by straightening machine.

 

Step 5: Connections process

Make holes on connected pieces by drilling machines. Make sure the hole size and precision.

 

 

 

Step 6: Welding

Welding with CO2. Make sure the weld quality without welding flaw.

 

 

Step 7: Shot blasting

Make shot blasting on steel profiles. Make sure the blasting grade and quality.

 

Step 8: Spray painting

Painting or other anti-corrosion surface treatment.

 

Step 9: Package & Loading

Pack steel structure profiles on steel pallet, which will be easy for loading, transportation and unloading jobs.

 

1. The positioning axis and supporting surface elevation of the foundation are out of tolerance:

The positioning axis of the foundation and the elevation of the supporting steel cylinder exceed the allowable deviation.

 

The reasons are as follows:

There are errors and deviations in foundation survey control network, foundation survey setting out and elevation finding.

The foundation formwork is not firmly set up, the pouring concrete blanking is too high, and the concrete is vibrated and impacted, which makes the formwork displacement and causes the datum line deviation.

Or the use of steel ruler, theodolite, level without calibration, there are errors.

Or construction wrong drawings, axis wrong, without strict inspection.

Or if the foundation bearing surface is not plastered and leveled twice, the concrete will shrink and sink.

Or the embedded steel plate (or support) is not fixed.

Because the foundation positioning axis and bearing surface are out of tolerance, the column installation axis and bearing elevation will be out of tolerance, which will affect the quality of the whole structural steel construction installation project.

 

Avoiding measures:

(1) The accuracy of basic survey control network, instruments and measuring tools used for basic survey setting out and leveling shall be accurate. Before use, they must be checked or verified by the measurement department. If problems are found, they shall be adjusted in time to prevent errors or accumulated errors, resulting in axis and elevation exceeding the allowable deviation.

(2) The foundation formwork for steel structure construction must be firmly supported with sufficient strength and rigidity. When pouring concrete, cutting and vibrating, it is necessary to prevent from striking the formwork and causing displacement. In the process of concrete pouring, the positioning axis and elevation shall be checked regularly with measuring tools or suspension lines. If any deviation is found, the pouring and vibration shall be stopped, and the work shall be carried out after reinforcement and adjustment. Before the final setting of concrete, the surface of foundation concrete shall be plastered and leveled twice. For the embedded steel plate or bearing, the elevation and levelness shall be aligned twice, and the concrete at the bottom shall be dense. The steel plate or support of foundation support column shall be provided with necessary fixing devices to ensure correct position and elevation.

(3) When the elevation and levelness of the steel plate or support on the vertical and horizontal axis of the foundation and column bearing surface are out of tolerance, measures shall be taken according to the degree of deviation. When the out of tolerance is not serious, it can be solved by shifting the column base, reaming and packing the base plate. If the deviation is serious and cannot be adjusted, it should be studied with relevant departments to work out a feasible correction scheme before treatment.

 

2. Foundation anchor bolt thread damage:

The foundation anchor bolt thread is damaged, and the nut cannot be screwed and tightened during the column installation.

 

The causes of bolt thread damage are as follows:

Anchor bolts are impacted or improperly kept during transportation, loading and unpacking, resulting in serious thread corrosion.

Or the bolts were not protected after burying and were damaged by outside.

Or the bolt is used as electric welding zero line on site, and the thread is damaged due to arc burn.

Or the bolt is used as the binding point of the pulling force of the traction rope.

Due to the damage of bolt thread, it is impossible to screw in nuts to fasten steel columns and other components, which affects the transmission and stability of structural force.

 

Avoiding measures:

(1) When the anchor bolts are transported, packed and unpacked, the thread protection shall be strengthened. After being smeared with industrial vaseline oil, they shall be wrapped and bound with plastic film to prevent thread damage and corrosion. And should be stored separately, should not be mixed with other parts and components, so as to avoid mutual impact damage thread.

(2) After the anchor bolt is embedded, it shall not be used as the fulcrum of bending processing, the neutral line of electric welding machine, or the binding point of traction force. When lifting components, proper operation shall be carried out to prevent the thread from being damaged by horizontal lateral impact force.

(3) The screw thread of the bolt has been damaged, and the following treatment methods can be adopted: when the damaged length of the screw thread does not exceed its effective length, the steel file can be used to trim the screw thread, so as to smoothly screw in the nut. When the length of thread damage of local foot bolt exceeds the specified effective length, the length of original thread section can be cut by gas cutting; Then, with the same material and specification as the original bolt, one end of the bolt is processed into thread, and the butt end section is made into 30º-- 45º. After butt welding with the lower end of the groove, the corresponding diameter specification and length of the steel casing sleeve into the joint, welding reinforcement. After casing reinforcement for steel work in construction, the diameter of the bolt will be larger than that of the base plate, which can be solved by appropriately enlarging the diameter of the base plate.

 

3. The setting of mortar base plate of column base does not meet the requirements:

The mortar base plate of column base is set randomly, and the elevation, levelness and position do not meet the design and specification requirements.

 

The reasons are as follows:

The surface of the foundation is not treated and leveled, so that the base plate can not bear the force smoothly, and the surface is uneven and uneven;

The base plate is not reasonably arranged according to the stress requirements, so that the base, base plate and foundation can not bear uniform pressure, so that the settlement of base slurry is uneven, and the elevation and levelness can not meet the requirements.

If the setting of open base plate does not meet the requirements, it can not transfer the load evenly, which will reduce the mechanical performance of the column and affect the stability of the superstructure.

 

Avoiding measures:

(1) In order to make the base plate group transmit the force to the foundation smoothly, the base plate should be closely combined with the base slurry on the foundation surface. The uneven foundation surface shall be chiseled and leveled.

(2) The location and distribution of the base plate should be correct. Generally, according to the stress area of the steel column base plate, the base plate, the base plate and the foundation should be arranged in the center of the steel plate and the stress concentration position on both sides or near the two sides of the anchor bolt, so that the base plate, the base plate and the foundation can fully bear the pressure load, and bear the force uniformly together to avoid partial bias Concentrated stress or deformation of the base plate occurs when the anchor bolts are tightened.

(3) The area of the base plate directly bearing the load should meet the needs of the stress, which should be determined by calculation, and the area should not be too large or too small. Too large will cause waste, too small will cause local concentrated overload of foundation and affect the overall and uniform stress of foundation. The thickness of the base plate is generally within the range of 4 ~ 25 mm, each group is no more than 3 pieces. The base plate has a 10 ~ 12 mm thick steel plate, the length of the base plate is 100 ~ 300 mm, and the width is 50 ~ 120 mm. When setting the mortar, use non shrinkage cement mortar with strength not lower than 30MPa. As the steel column is mainly installed with cushion plate to adjust the elevation and levelness, the elevation and levelness shall be found when grouting, and the allowable deviation shall comply with the specification, and the supervision shall be strengthened. Before the base plate is grouted, the rust, oil stain and burr on the surface of the base plate shall be cleaned, so that the base plate can be firmly combined with the concrete when grouted and grouted; The length of the base plate group exposed to the outside of the base plate edge is about 10 ~ 20 mm.

 

4. Before the installation of steel column, the foundation is directly installed without inspection:

Before the installation of steel column, the axis and elevation of the foundation, the position and elevation of the anchor bolt and the concrete quality of the foundation are not checked in advance, so the installation is carried out directly. In this way, there may be out of tolerance without repair, which will cause structural installation difficulties, increase the steel column installation stress and affect the installation accuracy, and even cause quality hazards.

 

Avoiding measures:

Before the installation of steel column, the positioning control line, foundation axis, elevation, anchor bolt position, elevation and concrete quality of foundation shall be pre checked. If the deviation is found, measures shall be taken to correct and adjust to the allowable deviation range of the specification. For elevation inspection, the measured data shall be compared with the pre inspection data of steel column size and elevation, and the error of the two shall be eliminated when the support base slurry pad or anchor bolt nut is adjusted. The allowable deviation of foundation support surface, anchor bolt position and base slurry pad shall meet the requirements of the specification. The quality of foundation concrete shall be dealt with in accordance with relevant regulations.

 

5. Don't check the dimension of steel members, deal with deformation and quality defects before installation

Before the installation of the structure, the external dimensions of the steel members are not checked, and the deformation and quality defects of the members are handled.

Although the steel components have passed the quality inspection before they are processed in the factory, they may fail to be inspected, or new deformation and damage may occur in the transportation and stacking of the components. If the review is not carried out before the installation, these problems can not be dealt with in time before the installation, which will affect the installation quality of the steel structure and cause installation difficulties or permanent quality defects.

 

Avoiding measures:

Before the installation of steel members, the steel members shall be carefully checked in advance:

It includes checking the model and quantity of the component, the overall dimension of the component, the relevant dimensions between the supporting surfaces and the installation holes, and marking the datum line of the axis of the component. Check whether the component is deformed, and correct and repair the deformation error if there is any.

Whether the connecting plate, splint and other accessories of the component are complete and whether the position and size are accurate. Inspect whether the surface quality of the welding area of the component and the friction surface of the high-strength bolt connection meet the requirements and whether it is polluted.

Whether the member nodes are complete and whether the center of gravity of main components is marked.

Whether the surface of the component is polluted, whether the paint falls off, etc.

Pre inspection records of components shall be made; For the components with deformation and defects exceeding the allowable deviation, they shall be corrected and repaired on the ground before installation, and can be installed after they are qualified.

 

6. The perpendicularity of steel column installation is out of tolerance:

The verticality deviation of steel column exceeds the allowable value in design or code

When the steel column is manufactured, the deformation control measures are not taken or the bending deformation is not straightened.

Or the length of the column is large, the rigidity is poor, and the elastic or plastic deformation occurs under the action of external force.

Or due to the unreasonable hoisting technology and procedure, the roof panel is bent and deformed under the action of temperature, wind and external force.

Or there is deviation in the span size of the roof truss, the external force is used to force the connection during the installation, resulting in the over deviation of the verticality of the steel column.

This will lead to the deflection of the steel column and affect the bearing capacity and stability.

 

Avoiding measures:

(1) Anti deformation measures shall be taken for assembly and welding of steel column, and the deformation during fabrication shall be corrected in time. When transporting and stacking steel columns, the supporting points should be appropriate to prevent bending deformation under the action of self weight. The out of plane stiffness of long column is poor, so the lifting point should be selected at 2 / 3 of the total length of the column to prevent deformation. If the span size of steel roof truss exceeds the deviation, it should be corrected before installation to prevent forced connection and bending deformation of column body.

(2) When the steel column is hoisted to the foundation plane in place, the vertical and horizontal axis above the column base plate should be aligned with the foundation line, so as to prevent the deviation of span size, which will lead to the horizontal tension or thrust when the column head is installed and connected with the roof truss, so as to make the column body bending and deformation, and carry out appropriate control.

(3) When the roof slab is hoisted after the connection and installation of the steel column and the tail-stock, it should be carried out symmetrically and synchronously from the edge of the two slopes in the center of the top chord to the middle, so as to prevent the bending deformation of the steel column caused by the lateral concentrated pressure generated by the one slope. Without the permission of the design, the steel column and other connected components shall not be used for horizontal dragging or vertical hoisting of heavy components and equipment, and the column bending deformation or damage to the connecting structure shall be prevented.

(4) If the bending steel column is elastic deformation, it can be restored to its original state after the external pressure is removed; If it is plastic deformation, it can be corrected by adding temporary support above or at the top of the bending part of the steel column before correction, so as to reduce the load-bearing gravity, and then fixing one side reaction frame at the bending part, and using jack for correction. If the rigidity of the steel column is large, it can be corrected by heating the bending convex surface with oxyacetylene flame, and then applying jacking force.

 

7. Steel column installation height is out of tolerance：

Height dimension or relative position of steel column after installation (±) The elevation dimension is out of tolerance, which makes the difference between the total height of each column and the height deviation of the bracket.

The reasons are as follows

Foundation elevation is incorrect or deviation occurs.

The length and dimension of steel column during the production stage are out of tolerance.

Or when the foundation elevation is adjusted and treated during installation, it is not combined with the actual length (height) of steel column, which will cause the positive or negative difference of the height dimension or elevation dimension of the steel column after installation.

Because of the over tolerance, it is difficult to install and adjust the components connected with it, which makes it difficult to correct and takes time.

Avoiding measures:

(1) During the foundation construction, the elevation size should be strictly controlled to ensure the accuracy of elevation. The elevation dimension of the upper surface of the foundation shall be adjusted according to the actual length of the steel column or the elevation dimension of the bracket supporting surface, so as to make it consistent with the height and elevation dimension of the steel column after installation.

(2) During the manufacturing process of steel column, the length and size (including the total length and the length of each position specified in the design, the length and size within the allowable positive and negative deviation range, and the positive excess value not allowed) and the correct size of the total length and bracket of the steel column without contact point shall be strictly controlled. The latter can be adopted to weld the column body first, and the column base plate and column head plate shall not be welded temporarily, In case of out of tolerance, adjust before welding the base plate or upper column head plate of the column, and finally weld the base plate and column head plate of the column.

Agricultural steel building components or parts are usually connected by welds, bolts or rivets. Because of its light weight and simple construction, it is widely used in various fields of agricultural production. Steel structure is easy to rust. Generally, steel structure needs to be derusted, galvanized or painted, and it needs to be maintained regularly. Here we are going to know more about the Agricultural steel building.

• What are the architectural characteristics of Agricultural steel buildings?

• What are the appearance characteristics of Agricultural steel building?

• What should be paid attention to when constructing Agricultural steel building?

What are the architectural characteristics of Agricultural steel buildings?

1. Industrialization of the production process. The steel structure is only connected by high-strength bolts. It also has the advantages of quick installation and return on investment.

2. Use high-quality materials with high toughness and plasticity. The quality is safe and reliable.

3. It also has the advantages of flexible design and decoration, low cost, and various colors.

What are the appearance characteristics of Agricultural steel building?

The Agricultural steel building has no beams and no purlins, wide space, large spanning capacity, and the span of 6-32 meters can be chosen at will. Low cost, low investment, economical. The design and construction period is short,

The roof construction of Agricultural steel building can be completed in 20 days. Colored galvanized steel sheet, mechanical seam connection, natural waterproof, no leakage.

The Agricultural steel building is beautiful in appearance, sturdy and durable, and requires no maintenance.

The Agricultural steel building is light in weight, the overall structure is scientific and reasonable, and the wind and seismic performance is superior. Wind resistance and snow load, can withstand strong winds of 160km/n per hour, and can withstand a snow load of 148kg.

The shape of Agricultural steel building is beautiful, colorful, novel and full of rhythm. Rich and diverse roof forms give the building a new appearance.

The Agricultural steel building has complete functions, the roof slab and beam are integrated, and it integrates multiple functions such as heat preservation, heat insulation, ventilation, and lighting.

What should be paid attention to when constructing Agricultural steel building?

1 Personnel engaged in high-altitude operations must hold a certificate to work, and earnestly abide by the safety construction regulations, wear flexible clothing, and it is forbidden to wear hard-soled and slippery shoes with nails;

2 Workers of Agricultural steel building wear safety belts;

3 A safety net is set under the working surface of Agricultural steel building;

4 Materials for high-altitude operations should be stacked steadily. They should not be placed on the edge or attached to the opening of the hole. If there is a possibility of falling, they should be withdrawn or fixed in time to prevent falling objects from injuring people.

The Agricultural steel buildings made by Qingdao Xinguangzheng Steel Structure Co., Ltd. feature attractive appearance, excellent performance, easy maintenance, and internationally advanced performance indicators, and are exported to more than 10 countries and regions.

The China Flower Fair, which was founded by our company in 1987, is the largest, highest-grade and most influential national flower event in China, and is known as the "Olympic" in the Chinese flower industry. Nowadays, there are many characteristic flower and tree fairs all over the country, such as China (Xiaxi) flower and tree Festival, China Flower Trade Conference, Zhengzhou International Flower and horticulture exhibition, Xiaoshan flower and tree Festival, Shuyang flower and tree Festival, etc.

Project picture of Steel Structure Conference center of China flower Expo.

Qingdao Xinguangzheng Company suppiler of Steel Structure Conference center of China flower Expo.

1200 workers, 360000 ㎡ non-dust workshop, 25 years experience, CE, ISO9001, ISO9712, ISO3834, BV, SGS certificated, one hour reach Qingdao port, our company, as a manufacture, this is how we keep good quality and competitive prices for global valued customers.

We provide steel building design, farm house design, manufacture and installation service.

Industrial steel building is easy to move and recycle without pollution. These are stronger than traditional workshops, and the walls of the steel structure workshops can also be filled with bricks, which are completely load-bearing. All future plant constructions will be steel structure plants. Here we are going to introduce the steps of installing Industrial steel building.

• What are the raw materials used in industrial steel building?

• What is the main installation process of industrial steel building?

• What is the production and installation process of industrial steel building?

What are the raw materials used in industrial steel building?

In addition to iron and carbon, the raw materials of industrial steel building also contain other elements. Divided into permanent elements; occasional elements; hidden elements and alloying elements. The common elements are manganese, silicon, sulfur, and phosphorus. Incidental elements are due to the different origins of ore (there are intergrowth ore mixed with iron) and scrap steel as raw materials, such as copper, titanium, vanadium, rare earth elements, etc., are brought into steel during smelting and process operations. The cryptic elements refer to non-metal elements with a small atomic radius, such as oxygen and hydrogen. Alloying elements refer to elements specially added to change the composition, such as chromium, nickel, tungsten, molybdenum, vanadium, etc.

Carbon steel (referred to as carbon steel) is an iron-carbon alloy with a carbon content of more than 0.0218% and less than 2.11%. Because carbon steel has good mechanical properties and process properties, and is large in output and low in price, it is a metal material that is widely used in mechanical engineering. However, carbon steel also has some shortcomings, such as low hardening energy, poor temper softening resistance, and low yield ratio. The strength potential of carbon steel cannot be fully utilized even after heat treatment. In order to meet the continuous development of modern industry and science and technology, alloy steel was developed.

What is the main installation process of industrial steel building?

Foundation → production and installation foundation is divided into (foundation ground survey → foundation excavation → embedded screws → foundation casting → later foundation grouting → outdoor water dispersion → outdoor drainage ditch (some factory design indoor drainage ditch or cable ditch suggestion Completed simultaneously with installation)→Enclosure masonry→tiling tiles, etc.)

What is the production and installation process of industrial steel building?

The production and installation are divided into (processing production→component painting→structural pre-assembly→steel component hoisting→main structure adjustment→purlin installation→door and window column installation→gutter downpipe installation→steel component painting (some are fireproof, some are Anti-corrosion, according to design requirements) → roof panel (some with steel mesh, some with insulation layer, completed at the same time) → wall panel installation → door and window installation → water supply and drainage installation → electrical equipment installation)

Qingdao Xinguangzheng Steel Structure Co., Ltd., as a Chinese pioneer in producing Industrial steel buildings, can ensure the products’ quality and the after-sales service.

25/11/2022· Create profitable strategy to export Structural steel beam from Canada with Top Structural steel beam exporting importing countries, Top Structural steel beam importers

Cooler Buildings Get Started with Your New Agricultural Steel Building Today Contact us today and we can have your new building ready to use in weeks. Our team of experts in agricultural buildings will guide you through the options and find the perfect fit for your budget. Get Started Or call (229)776-7588 Why Choose Rigid Frame Buildings?

Get Metal-Hanger Import Data Of India With Buyers And Suppliers’ Details, Shipment Date, Price, HS Code, Ports, Quantity And More. About Us Services Blogs Contact Us 91.120.4517800 91 9971093718 Help Desk Request Demo Menu Home Online India ...

The frame structure can provide ample internal space, make the layout of the building flexible, and is suitable for various types of utility functions. The steel structure is lightweight, excellent seismic performance, fast construction speed, and a high degree of mechanization. 2. The construction period is short.

Get multiple competitive quotes for free within one business day! Compare prices with deeply competitive quotes from suppliers in your area.

M.S.ENTERPRISES deals in all types of Metal Working Workshop Machines, Accessories and Spares with over 37 years of experience, hard work and dedication. The company provides a huge range of Quality Machines with Guaranteed Performance, Easy After Sales Services and availability of standard and interchangeable spares. General Industrial Machinery

QUALITY We at Starwire are a committed, competent and highly motivated Workforce, integrated into conducive and strong TQM culture. Starwire has the most modern Steel Manufacturing and Testing facilities in India.Our plants are certified to ISO 14001:2004, ISO 14001 TS 16949, OHSAS 18001:1999, TQM

We have capability in-house to carry out work from the supply of a basic steel-frame building, to a complete design